AEG Freezer S83600CSM1 User Manual

S83600CSM1  
EN FRIDGE FREEZER  
USER MANUAL  
 
Contents  
3
CONTENTS  
4 Safety information  
6 Control panel  
11 First use  
11 Daily use  
13 Helpful hints and tips  
15 Care and cleaning  
16 What to do if…  
18 Technical data  
18 Installation  
22 Noises  
24 Environmental concerns  
The following symbols are used in this user  
manual:  
Important information concerning your  
personal safety and information on how to  
avoid damaging the appliance.  
General information and tips  
Environmental information  
Subject to change without notice  
 
4
Safety information  
SAFETY INFORMATION  
In the interest of your safety and to ensure the correct use, before installing and first using  
the appliance, read this user manual carefully, including its hints and warnings. To avoid  
unnecessary mistakes and accidents, it is important to ensure that all people using the ap-  
pliance are thoroughly familiar with its operation and safety features. Save these instruc-  
tions and make sure that they remain with the appliance if it is moved or sold, so that ev-  
eryone using it through its life will be properly informed on appliance use and safety.  
For the safety of life and property keep the precautions of these user's instructions as the  
manufacturer is not responsible for damages caused by omission.  
Children and vulnerable people safety  
• This appliance is not intended for use by persons (including children) with reduced physi-  
cal, sensory or mental capabilities, or lack of experience and knowledge, unless they have  
been given supervision or instruction concerning use of the appliance by a person re-  
sponsible for their safety.  
Children should be supervised to ensure that they do not play with the appliance.  
• Keep all packaging well away from children. There is risk of suffocation.  
• If you are discarding the appliance pull the plug out of the socket, cut the connection  
cable (as close to the appliance as you can) and remove the door to prevent playing chil-  
dren to suffer electric shock or to close themselves into it.  
• If this appliance featuring magnetic door seals is to replace an older appliance having a  
spring lock (latch) on the door or lid, be sure to make that spring lock unusable before  
you discard the old appliance. This will prevent it from becoming a death trap for a child.  
General safety  
WARNING!  
Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of  
obstruction.  
• The appliance is intended for keeping foodstuff and/or beverages in a normal household  
as explained in this instruction booklet.  
• Do not use a mechanical device or any artificial means to speed up the thawing process.  
• Do not use other electrical appliances (such as ice cream makers) inside of refrigerating  
appliances, unless they are approved for this purpose by the manufacturer.  
• Do not damage the refrigerant circuit.  
• The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the appli-  
ance, a natural gas with a high level of environmental compatibility, which is neverthe-  
less flammable.  
During transportation and installation of the appliance, be certain that none of the com-  
ponents of the refrigerant circuit become damaged.  
If the refrigerant circuit should become damaged:  
– avoid open flames and sources of ignition  
 
Safety information  
– thoroughly ventilate the room in which the appliance is situated  
5
• It is dangerous to alter the specifications or modify this product in any way. Any damage  
to the cord may cause a short-circuit, fire and/or electric shock.  
WARNING!  
Any electrical component (power cord, plug, compressor) must be replaced by a certified  
service agent or qualified service personnel to avoid hazard.  
1. Power cord must not be lengthened.  
2. Make sure that the power plug is not squashed or damaged by the back of the ap-  
pliance. A squashed or damaged power plug may overheat and cause a fire.  
3. Make sure that you can come to the mains plug of the appliance.  
4. Do not pull the mains cable.  
5. If the power plug socket is loose, do not insert the power plug. There is a risk of  
electric shock or fire.  
6. You must not operate the appliance without the lamp cover (if foreseen) of interior  
lighting.  
• This appliance is heavy. Care should be taken when moving it.  
• Do not remove nor touch items from the freezer compartment if your hands are damp/  
wet, as this could cause skin abrasions or frost/freezer burns.  
• Avoid prolonged exposure of the appliance to direct sunlight.  
• Bulb lamps (if foreseen) used in this appliance are special purpose lamps selected for  
household appliances use only. They are not suitable for household room illumination.  
Daily Use  
• Do not put hot pot on the plastic parts in the appliance.  
• Do not store flammable gas and liquid in the appliance, because they may explode.  
• Do not place food products directly against the air outlet on the rear wall. (If the appli-  
ance is Frost Free)  
• Frozen food must not be re-frozen once it has been thawed out.  
• Store pre-packed frozen food in accordance with the frozen food manufacturer's in-  
structions.  
• Appliance's manufacturers storage recommendations should be strictly adhered to. Refer  
to relevant instructions.  
• Do not place carbonated or fizzy drinks in the freezer compartment as it creates pressure  
on the container, which may cause it to explode, resulting in damage to the appliance.  
• Ice lollies can cause frost burns if consumed straight from the appliance.  
Care and cleaning  
• Before maintenance, switch off the appliance and disconnect the mains plug from the  
mains socket.  
• Do not clean the appliance with metal objects.  
• Do not use sharp objects to remove frost from the appliance. Use a plastic scraper.  
 
6
Control panel  
• Regularly examine the drain in the refrigerator for defrosted water. If necessary, clean  
the drain. If the drain is blocked, water will collect in the bottom of the appliance.  
Installation  
For electrical connection carefully follow the instructions given in specific paragraphs.  
• Unpack the appliance and check if there are damages on it. Do not connect the appli-  
ance if it is damaged. Report possible damages immediately to the place you bought it.  
In that case retain packing.  
• It is advisable to wait at least four hours before connecting the appliance to allow the oil  
to flow back in the compressor.  
• Adequate air circulation should be around the appliance, lacking this leads to overheat-  
ing. To achieve sufficient ventilation follow the instructions relevant to installation.  
• Wherever possible the back of the product should be against a wall to avoid touching or  
catching warm parts (compressor, condenser) to prevent possible burn.  
• The appliance must not be located close to radiators or cookers.  
• Make sure that the mains plug is accessible after the installation of the appliance.  
• Connect to potable water supply only (If a water connection is foreseen).  
Service  
• Any electrical work required to do the servicing of the appliance should be carried out by  
a qualified electrician or competent person.  
• Do not remove the LED light cover. Contact the nearest After Sales Service Force to re-  
place the LED light board, if it is necessary.  
• This product must be serviced by an authorized Service Centre, and only genuine spare  
parts must be used.  
Environment Protection  
This appliance does not contain gasses which could damage the ozone layer, in either its  
refrigerant circuit or insulation materials. The appliance shall not be discarded together  
with the urban refuse and rubbish. The insulation foam contains flammable gases: the ap-  
pliance shall be disposed according to the applicable regulations to obtain from your local  
authorities. Avoid damaging the cooling unit, especially at the rear near the heat exchang-  
er. The materials used on this appliance marked by the symbol  
are recyclable.  
CONTROL PANEL  
1
2
3
4
5
6
7
8
Appliance ON/OFF button  
1
 
Control panel  
7
Fridge Temperature colder button  
Fridge Temperature warmer button  
Mode button  
2
3
4
5
6
7
8
OK button  
Freezer Temperature colder button  
Freezer Temperature warmer button  
Display  
It is possible to change predefined sound of buttons to a loudly one by pressing together  
Mode button and Temperature colder button for some seconds. Change is reversible.  
Display  
1
2
3
4
5
6
7
COOL  
MATIC  
FROST  
MATIC  
Off  
min  
11 10 9  
8
Fridge compartment indicator  
1
2
3
4
5
6
7
8
9
Fridge temperature indicator and timer indicator  
Fridge off indicator  
COOLMATIC function  
Holiday function  
FROSTMATIC function  
Freezer temperature indicator  
Freezer compartment indicator  
Alarm indicator  
Child Lock function  
10  
11  
Minute Minder function  
Switching on  
To switch on the appliance do these steps:  
1. Connect the mains plug to the power socket.  
2. Press the appliance ON/OFF button if the display is off.  
3. The alarm buzzer could operate after few seconds.  
To reset the alarm refer to "High temperature alarm".  
4. If "dEMo" appears on the display, the appliance is in demonstration mode. Refer to  
"What to do if...".  
5. The temperature indicators show the set default temperature.  
To select a different set temperature refer to "Temperature regulation".  
 
8
Control panel  
Switching off  
To switch off the appliance do these steps:  
1. Press the appliance ON/OFF button for 5 seconds.  
2. The display switches off.  
3. To disconnect the appliance from the power disconnect the mains plug from the pow-  
er socket.  
Switching off the fridge  
To switch off the fridge:  
1. Press the Mode button until the corresponding icon appears.  
The fridge Off indicator and the fridge compartment indicator flash.  
The fridge temperature indicator shows dashes.  
2. Press the OK button to confirm.  
3. The fridge Off indicator is shown.  
Switching on the fridge  
To switch on the fridge:  
1. Press the fridge temperature regulator.  
Or:  
1. Press the Mode button until the corresponding icon appears.  
The Fridge Off indicator flashes.  
2. Press the OK button to confirm.  
3. The fridge Off indicator goes off.  
To select a different set temperature refer to "Temperature regulation".  
Temperature regulation  
The set temperature of the fridge and of the freezer may be adjusted by pressing the tem-  
perature regulators.  
Set default temperature:  
• +5°C for the fridge  
-18°C for the freezer  
The temperature indicators show the set temperature.  
The set temperature will be reached within 24 hours.  
Fluctuations of some degrees around set temperature are normal and does not mean any  
fault in the appliance.  
After a power failure the set temperature remains stored.  
Minute Minder function  
The Minute Minder function is to be used to set an acoustic alarm at the preferred time,  
useful for example when a recipe requires to cool down a mixture for a certain lenght of  
time, or when a reminder is needed in order not to forget the bottles placed in the freezer  
for fast cooling.  
To switch on the function:  
 
Control panel  
9
1. Press the Mode button until the corresponding icon appears.  
The Minute Minder indicator flashes.  
The Timer shows the set value (30 minutes) for a few seconds.  
2. Press the Fridge Temperature button to change the Timer set value from 1 to 90 mi-  
nutes.  
3. Press the OK button to confirm.  
The Minute Minder indicator is shown.  
The Timer start to flash (min).  
At the end of the countdown the Minute Minder indicator flashes and an audible alarm  
sounds:  
1. Remove any drinks contained in the freezer compartment.  
2. Press OK button to switch off the sound and terminate the function.  
It is possible to deactivate the function at any time during the countdown:  
1. Press the Mode button until the Minute Minder indicator flashes.  
2. Press the OK button to confirm.  
3. The Minute Minder indicator goes off.  
It is possible to change the time during the countdown and at the end by pressing the  
Fridge Temperature colder button or the Fridge Temperature warmer button.  
Child Lock function  
To lock the buttons from unintentional operation select the Child Lock function.  
To switch on the function:  
1. Press the Mode button until the corresponding icon appears.  
2. The Child Lock indicator flashes.  
3. Press the OK button to confirm.  
The Child Lock indicator is shown.  
To switch off the function:  
1. Press the Mode button until the Child Lock indicator flashes.  
2. Press the OK button to confirm.  
3. The Child Lock indicator goes off.  
High temperature alarm  
An increase in the temperature in the freezer compartment (for example due to an earlier  
power failure) is indicated by:  
• flashing the alarm and freezer temperature indicators  
• sounding of buzzer.  
To reset the alarm:  
1. Press any button.  
2. The buzzer switches off.  
3. The freezer temperature indicator shows the highest temperature reached for a few  
seconds. Then show again the set temperature.  
4. The alarm indicator continue to flash until the normal conditions are restored.  
When the alarm has returned the alarm indicator goes off.  
 
10  
Control panel  
Door open alarm  
An acoustic alarm will sound if the fridge door is left open for a few minutes. The door  
open alarm conditions are indicated by:  
• flashing Alarm indicator  
• acoustic buzzer  
When normal conditions are restored (door closed), the alarm will stop.  
COOLMATIC function  
If you need to insert a large amount of warm food, for example after doing the grocery  
shopping, we suggest activating the COOLMATIC function to chill the products more rapidly  
and to avoid warming the other food which is already in the refrigerator.  
To switch on the function:  
1. Press the Mode button until the corresponding icon appears.  
The COOLMATIC indicator flashes.  
2. Press the OK button to confirm.  
The COOLMATIC indicator is shown.  
The COOLMATIC function shuts off automatically after approximately 6 hours.  
To switch off the function before its automatic end:  
1. Press the Mode button until the COOLMATIC indicator flashes.  
2. Press the OK button to confirm.  
3. The COOLMATIC indicator goes off.  
The function switches off by selecting a different fridge set temperature.  
Holiday function  
This function allows you to keep the refrigerator closed and empty during a long holiday  
period without the formation of a bad smell.  
The fridge compartment must be empty with holiday function on.  
To switch on the function:  
1. Press the Mode button until the corresponding icon appears.  
The Holiday indicator flashes.  
The fridge temperature indicator shows the set temperature.  
2. Press the OK button to confirm.  
The Holiday indicator is shown.  
To switch off the function:  
1. Press the Mode button until the Holiday indicator flashes.  
2. Press the OK button to confirm.  
3. The Holiday indicator goes off.  
The function switches off by selecting a different fridge set temperature.  
 
First use  
11  
FROSTMATIC function  
To switch on the function:  
1. Press the Mode button until the corresponding icon appears.  
The FROSTMATIC indicator flashes.  
2. Press the OK button to confirm.  
The FROSTMATIC indicator is shown.  
This function stops automatically after 52 hours.  
To switch off the function before its automatic end:  
1. Press the Mode button until the FROSTMATIC indicator flashes.  
2. Press the OK button to confirm.  
3. The FROSTMATIC indicator goes off.  
Place the fresh food to be frozen in the FROSTMATIC basket.  
The function switches off by selecting a different freezer set temperature.  
FIRST USE  
Cleaning the interior  
Before using the appliance for the first time, wash the interior and all internal accessories  
with lukewarm water and some neutral soap so as to remove the typical smell of a brand-  
new product, then dry thoroughly.  
Do not use detergents or abrasive powders, as these will damage the finish.  
DAILY USE  
Freezing fresh food  
The freezer compartment is suitable for freezing fresh food and storing frozen and deep-  
frozen food for a long time.  
To freeze fresh food activate the FROSTMATIC function at least 24 hours before placing the  
food to be frozen in the freezer compartment.  
Place the fresh food to be frozen in the FROSTMATIC compartment.  
The maximum amount of food that can be frozen in 24 hours is specified on the rating  
plate, a label located on the inside of the appliance.  
The freezing process lasts 24 hours: during this period do not add other food to be frozen.  
Thawing  
Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compart-  
ment or at room temperature, depending on the time available for this operation.  
Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking  
will take longer.  
 
12  
Daily use  
Movable shelves  
The walls of the refrigerator are equipped  
with a series of runners so that the shelves  
can be positioned as desired.  
Bottle rack  
Place the bottles (with the opening facing front)  
in the pre-positioned shelf.  
If the shelf is positioned horizontally, place only  
closed bottles.  
This bottle holder shelf can be tilted in order to  
store previously opened bottles. To obtain this re-  
sult, pull the shelf up so it can rotate upwards and  
be placed on the next higher level.  
FRESHBOX drawer  
The drawer is suitable for storing fresh food like  
fish, meat, seafood, because the temperature is  
lower here than in the rest of the fridge.  
Positioning the door shelves  
To permit storage of food packages of various  
sizes, the door shelves can be placed at different  
heights.  
To make these adjustments proceed as follows:  
gradually pull the shelf in the direction of the ar-  
rows until it comes free, then reposition as re-  
quired.  
1
2
3
 
Helpful hints and tips  
13  
MAXIBOX drawer  
The drawer is suitable for storing fruit and vege-  
tables.  
There is a separator inside the drawer that can be  
placed in different positions to allow for the sub-  
division best suited to personal needs.  
There is a grille (if foreseen) on the bottom of the  
drawer to separate the fruit and vegetables from  
any humidity that may form on the bottom sur-  
face.  
All parts inside the drawer can be removed for  
cleaning purposes  
Removal of freezing baskets from the freezer  
The freezing baskets have a limit stop to prevent  
their accidental removal or falling out. At the  
time of its removal from the freezer, pull the bas-  
ket towards yourself and, upon reaching the end  
point, remove the basket by tilting its front up-  
wards.  
At the time of putting it back, slightly lift the  
front of the basket to insert it into the freezer.  
Once you are over the end points, push the bas-  
kets back in their position.  
2
1
HELPFUL HINTS AND TIPS  
Normal Operating Sounds  
• You may hear a faint gurgling and a bubbling sound when the refrigerant is pumped  
through the coils or tubing. This is correct.  
• When the compressor is on, the refrigerant is being pumped around and you will hear a  
whirring sound and a pulsating noise from the compressor. This is correct.  
• The thermic dilatation might cause a sudden cracking noise. It is natural, not dangerous  
physical phenomenon. This is correct.  
Hints for energy saving  
To obtain the best performance:  
• do not open the door frequently or leave it open longer than absolutely necessary  
• do not remove the cold accumulators from the freezer basket.  
Hints for fresh food refrigeration  
To obtain the best performance:  
• do not store warm food or evaporating liquids in the refrigerator  
• do cover or wrap the food, particularly if it has a strong flavour  
 
14  
Helpful hints and tips  
• position food so that air can circulate freely around it  
Hints for refrigeration  
Useful hints:  
Meat (all types) : wrap in polythene bags and place on the glass shelf above the vegetable  
drawer.  
For safety, store in this way only one or two days at the most.  
Cooked foods, cold dishes, etc..: these should be covered and may be placed on any shelf.  
Fruit and vegetables: these should be thoroughly cleaned and placed in the special draw-  
er(s) provided.  
Butter and cheese: these should be placed in special airtight containers or wrapped in alu-  
minium foil or polythene bags to exclude as much air as possible.  
Milk bottles: these should have a cap and should be stored in the bottle rack on the door.  
Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator.  
Hints for freezing  
To help you make the most of the freezing process, here are some important hints:  
• the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating  
plate;  
• the freezing process takes 24 hours. No further food to be frozen should be added during  
this period;  
• only freeze top quality, fresh and thoroughly cleaned, foodstuffs;  
• prepare food in small portions to enable it to be rapidly and completely frozen and to  
make it possible subsequently to thaw only the quantity required;  
• wrap up the food in aluminium foil or polythene and make sure that the packages are  
airtight;  
• do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding a  
rise in temperature of the latter;  
• lean foods store better and longer than fatty ones; salt reduces the storage life of food;  
• water ices, if consumed immediately after removal from the freezer compartment, can  
possibly cause the skin to be freeze burnt;  
• it is advisable to show the freezing in date on each individual pack to enable you to keep  
tab of the storage time.  
Hints for storage of frozen food  
To obtain the best performance from this appliance, you should:  
• make sure that the commercially frozen foodstuffs were adequately stored by the retail-  
er;  
• be sure that frozen foodstuffs are transferred from the foodstore to the freezer in the  
shortest possible time;  
• not open the door frequently or leave it open longer than absolutely necessary;  
• once defrosted, food deteriorates rapidly and cannot be refrozen;  
• do not exceed the storage period indicated by the food manufacturer.  
 
Care and cleaning  
15  
CARE AND CLEANING  
CAUTION!  
Unplug the appliance before carrying out any maintenance operation.  
This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must  
therefore only be carried out by authorized technicians.  
Periodic cleaning  
The equipment has to be cleaned regularly:  
• clean the inside and accessories with lukewarm water and some neutral soap.  
• regularly check the door seals and wipe clean to ensure they are clean and free from  
debris.  
• rinse and dry thoroughly.  
Do not pull, move or damage any pipes and/or cables inside the cabinet.  
Never use detergents, abrasive powders, highly perfumed cleaning products or wax polishes  
to clean the interior as this will damage the surface and leave a strong odour.  
Clean the condenser (black grill) and the compressor at the back of the appliance with a  
brush. This operation will improve the performance of the appliance and save electricity  
consumption.  
Take care of not to damage the cooling system.  
Many proprietary kitchen surface cleaners contain chemicals that can attack/damage the  
plastics used in this appliance. For this reason it is recommended that the outer casing of  
this appliance is only cleaned with warm water with a little washing-up liquid added.  
After cleaning, reconnect the equipment to the mains supply.  
Defrosting of the refrigerator  
Frost is automatically eliminated from the  
evaporator of the refrigerator compartment  
every time the motor compressor stops,  
during normal use. The defrost water drains  
out through a trough into a special con-  
tainer at the back of the appliance, over the  
motor compressor, where it evaporates.  
It is important to periodically clean the de-  
frost water drain hole in the middle of the  
refrigerator compartment channel to pre-  
vent the water overflowing and dripping  
onto the food inside. Use the special clean-  
er provided, which you will find already in-  
serted into the drain hole.  
 
16  
What to do if…  
Defrosting the freezer  
A certain amount of frost will always form on the freezer shelves and around the top com-  
partment.  
Defrost the freezer when the frost layer reaches a thickness of about 3-5 mm.  
To remove the frost, follow the instructions below:  
• pull out the plug from the wall socket or switch off the appliance  
• remove any stored food, wrap it in several layers of newspaper and put it in a cool place  
• remove the freezer drawers  
• put insulating material around the drawers, e.g. blankets or newspapers.  
Defrosting can be accelerated by placing bowls  
with hot water (not boiling) inside the freezer.  
• Loosen the drainage channel from its resting  
position, push it in according to the illustration  
and place it in the bottom freezer drawer  
where water can collect  
• carefully scrape off the ice when it starts to  
thaw. Use a wood or a plastic scraper  
• when all the ice has melted, clean and wipe the  
cabinet dry, then put the drainage channel  
back in place.  
• switch on the cabinet and replace the frozen foodstuff.  
It is recommended to operate the appliance at the highest position of the thermostatic  
control for some hours so that it can reach the sufficient storing temperature as soon  
as possible.  
Never use sharp metal tools to scrape off frost from the evaporator as you could damage it.  
Do not use a mechanical device or any artificial means to speed up the thawing process  
other than those recommended by the manufacturer. A temperature rise of the frozen food  
packs, during defrosting, may shorten their safe storage life.  
WHAT TO DO IF…  
CAUTION!  
Before troubleshooting, disconnect the power supply.  
Only a qualified electrician or competent person must do the troubleshooting that is not in  
this manual.  
There are some sounds during normal use (compressor, refrigerant circulation).  
Problem  
Possible cause  
Solution  
The appliance is noisy.  
The appliance is not supported  
properly.  
Check if the appliance stands sta-  
ble (all the four feet should be on  
the floor).  
 
What to do if…  
17  
Problem  
Possible cause  
Solution  
The compressor operates  
continually.  
The Temperature regulator may Set a warmer temperature.  
be set incorrectly.  
The door is not closed correctly. Refer to "Closing the door".  
The door has been opened too  
frequently.  
Do not keep the door open longer  
than necessary.  
The product temperature is too  
high.  
Let the product temperature de-  
crease to room temperature be-  
fore storage.  
The room temperature is too  
high.  
Decrease the room temperature.  
Refer to "FROSTMATIC function".  
Refer to "COOLMATIC function".  
The FROSTMATIC function is  
switched on.  
The COOLMATIC function is  
switched on.  
Water flows on the rear  
plate of the refrigerator.  
During the automatic defrosting This is correct.  
process, frost defrosts on the  
rear plate.  
Water flows into the re-  
frigerator.  
The water outlet is clogged.  
Clean the water outlet.  
Products prevent that water  
flows into the water collector.  
Make sure that products do not  
touch the rear plate.  
Water flows on the  
ground.  
The melting water outlet does  
not flow in the evaporative tray to the evaporative tray.  
above the compressor.  
Attach the melting water outlet  
There is too much frost  
and ice.  
Products are not wrapped prop- Wrap the products better.  
erly.  
The door is not closed correctly. Refer to "Closing the door".  
The temperature in the refriger- Set a higher temperature.  
ator is too low.  
The temperature in the  
appliance is too high.  
The door is not closed correctly. Refer to "Closing the door".  
The product temperature is too  
high.  
Let the product temperature de-  
crease to room temperature be-  
fore storage.  
Many products are stored at the Store less products at the same  
same time. time.  
The temperature in the re- There is no cold air circulation in Make sure that there is cold air  
frigeration is too high.  
the appliance.  
circulation in the appliance.  
The temperature in the  
freezer is too high.  
Products are too near to each  
other.  
Store products so that there is  
cold air circulation.  
 
18  
Technical data  
Problem  
Possible cause  
Solution  
The appliance does not  
operate.  
The appliance is switched off.  
Switch on the appliance.  
The mains plug is not connected Connect the mains plug to the  
to the mains socket correctly.  
mains socket correctly.  
The appliance has no power.  
Connect a different electrical ap-  
There is no voltage in the mains pliance to the mains socket. Con-  
socket.  
tact a qualified electrician.  
The lamp does not work.  
The lamp is in stand-by.  
Close and open the door.  
"dEMo" appears on the  
display.  
The appliance is in demonstra-  
tion mode.  
Keep pressed approximately 10  
sec the OK button since a long  
sound of buzzer is heard and the  
display shut off for a short while:  
appliance start works regularly.  
As much as the advice does not lead to result, call the nearest brand-mark service.  
Closing the door  
1. Clean the door gaskets.  
2. If necessary, adjust the door. Refer to "Installation".  
3. If necessary, replace the defective door gaskets. Contact the Service Center.  
TECHNICAL DATA  
Dimension  
Height  
Width  
Depth  
1850 mm  
595 mm  
660 mm  
20 h  
Rising Time  
Voltage  
230 - 240 V  
50 Hz  
Frequency  
The technical information are situated in the rating plate on the internal left side of the  
appliance and in the energy label.  
INSTALLATION  
WARNING!  
Read the "Safety Information" carefully for your safety and correct operation of the appli-  
ance before installing the appliance.  
 
Installation  
19  
Positioning  
Install this appliance at a location where the ambient temperature corresponds to the cli-  
mate class indicated on the rating plate of the appliance:  
Climate class  
Ambient temperature  
SN  
N
+10°C to + 32°C  
+16°C to + 32°C  
+16°C to + 38°C  
+16°C to + 43°C  
ST  
T
Location  
The appliance should be installed well away from  
sources of heat such as radiators, boilers, direct  
sunlight etc. Ensure that air can circulate freely  
around the back of the cabinet. To ensure best  
performance, if the appliance is positioned below  
an overhanging wall unit, the minimum distance  
between the top of the cabinet and the wall unit  
must be at least 100 mm . Ideally, however, the  
appliance should not be positioned below over-  
hanging wall units. Accurate levelling is ensured  
by one or more adjustable feet at the base of the  
cabinet.  
WARNING!  
It must be possible to disconnect the appliance  
from the mains power supply; the plug must therefore be easily accessible after installation.  
Electrical connection  
Before plugging in, ensure that the voltage and frequency shown on the rating plate corre-  
spond to your domestic power supply.  
The appliance must be earthed. The power supply cable plug is provided with a contact for  
this purpose. If the domestic power supply socket is not earthed, connect the appliance to a  
separate earth in compliance with current regulations, consulting a qualified electrician.  
The manufacturer declines all responsibility if the above safety precautions are not ob-  
served.  
This appliance complies with the E.E.C. Directives.  
 
20  
Installation  
Rear spacers  
You can find the two spacers in the bag with doc-  
umentation.  
2
Do these steps to install the spacers:  
1. Release the screw.  
2. Engage the spacer below the screw.  
3. Turn the spacer to the right position.  
4. Tighten again the screws.  
1
3
4
Levelling  
When placing the appliance ensure that it stands  
level. This can be achieved by two adjustable feet  
at the bottom in front.  
Removing the shelf holders  
Your appliance is equipped with shelf retainers  
that make it possible to secure the shelves during  
transportation.  
A
To remove them proceed as follows:  
1. Move the shelf holders in the direction of the  
arrow (A).  
2. Raise the shelf from the rear and push it for-  
ward until it is freed (B).  
B
3. Remove the retainers (C).  
C
Door reversibility  
WARNING!  
Before carrying out any operations, remove the plug from the power socket.  
To carry out the following operations, we suggest that this be made with another person  
that will keep a firm hold on the doors of the appliance during the operations.  
 
Installation  
21  
1. Open the doors. Unscrew the middle  
hinge (m2). Remove the plastic spacer  
(m1).  
2. Remove the spacer (m6) and move to  
the other side of the hinge pivot (m5).  
m1  
m5  
m2  
m6  
3. Remove the doors.  
4. Remove the left-hand cover pin of the  
middle hinge (m3,m4) and move to the  
other side.  
5. Fit the pin of the middle hinge (m5) into  
the left-hand hole of the lower door.  
m4  
m3  
6. Remove using a tool the cover (b1). Un-  
screw the lower hinge pivot (b2) and the  
spacer (b3) and place them on the op-  
posite side.  
b1  
7. Re-insert the cover (b1) on the opposite  
side.  
b2  
b3  
8. Remove the handle. Unscrew the top  
handle bracket from the handle rod (h1).  
Unscrew the bottom handle bracket  
from the door (h2)  
h1  
h2  
h3  
Unscrew the top handle bracket from  
the door (h3).  
9. Install the handle in the opposite side.  
h4  
h5  
h6  
Re-screw the handle bracket on the  
door (h4). Turn the handle bracket with  
the handle and screw them to the door  
(h5) and the fitted handle bracket (h6).  
10. Remove using a tool the cover. (c1).  
Unscrew the upper hinge pivot (c2) and  
place it on the opposite side.  
11.  
 
22  
Noises  
C1  
C3  
C2  
C4  
12. Re-screw the upper hinge.  
13. Fit the upper door on the upper door  
pivot.  
14. Re-insert the upper door on the middle  
hinge pivot (c3 )slightly tilting both  
doors.  
15. Re-screw the middle hinge. Do not for-  
get the plastic spacer.  
1
2
2
1
Do a final check to make sure that:  
• All screws are tightened.  
• The magnetic seal adheres to the cabinet.  
• The door opens and closes correctly.  
If the ambient temperature is cold (i.e. in  
Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural  
fitting of the gasket.  
In case you do not want to carry out the above mentioned operations, contact the nearest  
After Sales Service Force. The After Sales Service specialist will carry out the reversibility of  
the doors at your cost.  
NOISES  
There are some sounds during normal running (compressor, refrigerant circulation).  
HISSS!  
BRRR!  
OK  
CLICK!  
CLICK!  
 
Noises  
23  
BRRR!  
BRRR!  
BLUBB!  
BLUBB!  
HISSS!  
HISSS!  
SSSRRR!  
SSSRRR!  
 
24  
Environmental concerns  
CRACK!  
CRACK!  
ENVIRONMENTAL CONCERNS  
The symbol on the product or on its packaging indicates that this product may not be  
treated as household waste. Instead it should be taken to the appropriate collection point  
for the recycling of electrical and electronic equipment. By ensuring this product is  
disposed of correctly, you will help prevent potential negative consequences for the  
environment and human health, which could otherwise be caused by inappropriate waste  
handling of this product. For more detailed information about recycling of this product,  
please contact your local council, your household waste disposal service or the shop where  
you purchased the product.  
 
25  
 
26  
 
27  
 
210622242-A-372011  
 

Accton Technology Switch ES4324 User Manual
Acoustic Research Radio ARIR150 User Manual
AEG Cooktop CGA 60 WOK User Manual
Airlink101 TV Converter Box ATVC101 User Manual
Alliance Laundry Systems Washer HC25SN SC80SN User Manual
Allied Telesis Freezer 6870 User Manual
Amana Freezer Deepfreeze Chest Freezer User Manual
Axis Communications Security Camera AXIS P5522E User Manual
Behringer Recording Equipment C 1 User Manual
Beko Planer DRCS 76 S User Manual