AEG Washer 84749 User Manual

ÖKO-LAVAMAT 84749 update  
The environmentally friendly washing machine  
User information  
 
Contents  
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Environmental tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
6
6
8
8
Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
9
9
9
Detergent dispenser drawer  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Programme selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Programme Option Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Programmable functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Consumption Values and Programme Times . . . . . . . . . . . . . . . . . . . . . . 14  
Wash Time Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
What does "UPDATE" mean? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Anti-flood Aqua Control + Aqua Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Before the first wash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Preparing for a wash cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Sorting and preparing the washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Types of washing and care symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Detergents and Conditioners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Which detergent and conditioner? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
How much detergent and conditioner? . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Water softening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Running a washing cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Brief instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Setting the wash programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Changing Spin Speed /selecting RINSE HOLD . . . . . . . . . . . . . . . . . . . . . . . . 20  
Setting the delay timer/soaking duration . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Opening and closing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Loading the washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Adding detergent/conditioners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Starting the wash programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
3
 
Washing Programme Progress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Washing cycle complete/Removing the washing . . . . . . . . . . . . . . . . . . . . 26  
Programme Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Separate Rinse/Conditioning/Starching/Treating . . . . . . . . . . . . . . . . . . . . 28  
Separate Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Maintenance and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Detergent Dispenser Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Washing Machine Drum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Main door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Cleaning the drain pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
What to do if... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
If the washing results are not satisfactory . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
Carrying out an emergency emptying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Emergency unlocking of the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
Additional rinse cycle (RINSE+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
Water cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
Additional rinse cycle and water cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
Variomatic spin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
Programme Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
Child Safety Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
Installation and connection instructions . . . . . . . . . . . . . . . . 44  
Installation Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
Installation of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Transporting the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Remove transport packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Installation-Site preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Installation on a Suspended Floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Levelling the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
4
 
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49  
Water connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51  
Water pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51  
Inlet Hose Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
Water Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53  
Pump head of greater than 1m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54  
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
Warranty conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56  
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58  
Service & Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59  
5
 
Operating Instructions  
Operating Instructions  
1 Safety  
The safety features of AEG electrical appliances comply with accepted  
technical standards and the German Appliance Safety Law. However, we  
also consider it our obligation as a manufacturer to inform you about  
the following safety information.  
Prior to initial start-up  
Observe the "Installation and Connection Instructions" in this in-  
struction book.  
If the appliance is delivered in the winter months and temperatures  
are below freezing: Store the washing machine at room temperature  
for a few hours before putting it into operation.  
Intended Use  
The washing machine is only intended for washing normal domestic  
washing. If the appliance is used for any other purpose or incorrectly  
operated, the manufacturer accepts no liability for any damages  
which may result.  
It is dangerous to alter the specifications or attempt to modify this  
product in any way.  
Only use detergents which are suitable for automatic washing ma-  
chines, and follow the recommendations of the detergent manufac-  
turer.  
Garments which have been in contact with flammable solvents  
should not be washed. Also bear this in mind when washing pre-  
cleaned washing.  
Do not use the washing machine for dry-cleaning.  
Dyes and bleaching agents may only be used if specifically permitted  
by the manufacturer of these products. We cannot be held liable for  
any damages.  
This appliance must be connected to the cold water supply only.  
Damage due to frost is not covered by the guarantee. If the washing  
machine is located in a room in which below freezing temperatures  
may occur, emergency emptying must be carried out (see "carrying  
out an emergency emptying“).  
6
 
Operating Instructions  
Child Safety  
Packaging materials (e.g. films, styrofoam) can be dangerous for chil-  
dren. There is a risk of suffocation! Keep all packaging well away from  
children.  
This appliance is designed to be operated by adults. Do not allow  
children to tamper with the controls or play with the appliance.  
Pets and children have been known to climb into washing machines.  
Please check the drum before use.  
When disposing of the appliance, cut off the mains cable, and destroy  
the plug. Disable the door lock to prevent young children being  
trapped inside.  
General Safety  
Repairs to the washing machine must only be carried out by qualified  
personnel. Repairs carried out by inexperienced persons may cause  
injury or serious malfunctioning. Contact your local AEG Service  
Force Centre.  
Never operate the washing machine if the mains cable is damaged or  
the control panel, work top or base area are damaged allowing inter-  
nal components to be accessible.  
Switch off the appliance and isolate from the mains supply before  
carrying out any cleaning or maintenance work.  
Do not use the mains cable to pull the plug out of the socket.  
Adapters and extension cables must not be used. There is a danger  
of overheating!  
Do not clean the washing machine with a water jet. There is a danger  
of electrical shock!  
During high temperature wash programmes, the glass of the door  
may become hot. Do not touch!  
Allow the water to cool down before cleaning the drain pump, carry-  
ing out emergency emptying or opening the door in an emergency.  
Small animals/pets can chew on power cables and water hoses. This  
can cause the danger of an electrical shock to the animal and water  
damage to the appliance and property. Keep small animals away from  
the appliance.  
7
 
Operating Instructions  
2 Disposal  
Packaging  
Dispose of the packaging material correctly. All packaging materials  
used are environmentally friendly and can be disposed of without any  
danger to the environment.  
Plastic parts can be recycled and are identified as follows:  
for polyethylene, e.g. the outer covering and the bags in  
the interior.  
>PE<  
>PS<  
for polystyrene, e.g. padding (always CFC-free)  
>POM< for polyoxymethylene, e.g. plastic clips  
Cardboard packaging is manufactured from recycled paper and  
should be deposited in the waste paper collection for recycling.  
When disposing of the washing machine!  
Cut off the mains cable and destroy the plug. Disable the door catch to  
prevent young children becoming trapped inside. Use an authorised  
disposal site.  
2 Environmental tips  
It is not usually necessary to Pre-wash or Soak normally soiled wash-  
ing. This will save you detergent, water and time (and protect the en-  
vironment as well).  
It is more economical to wash full loads.  
When washing small loads, use half to two thirds the recommended  
quantity of detergent.  
Pre-treat stains, if necessary, and then wash at a lower temperature.  
It can be possible to wash without fabric softeners, if clothes are  
dried in a tumble dryer, as this can give soft and fluffy results.  
In hard water areas, the use of a water softening agent can reduce  
the amount of detergent necessary. See manufacturer’s recommen-  
dations.  
8
 
Operating Instructions  
Description of the Appliance  
Front view  
Detergent  
dispenser  
drawer  
Control panel  
Rating plate  
(behind door)  
Main door  
Screw feet  
(height-adjustable);  
rear left:  
Automatic  
Flap in front of  
drain pump  
adjustment foot.  
Detergent dispenser drawer  
Stain removers  
Pre-wash detergent/  
soaking agent or  
water softening  
agent if used.  
Main wash detergent  
in powder form and  
water softening  
agent if required.  
Liquid conditioners  
(fabric softener,  
starch)  
9
 
Operating Instructions  
Control Panel  
Programme  
Progress-Display  
Spin speed/  
RINSE HOLD button  
Additional Programme-  
Options  
Programme Selector  
DOOR button  
START/  
PAUSE  
Button  
Multi display  
OVERDOSING indicator  
DELAY TIMER Button  
Programme selector  
The programme selector is used  
to select the type of wash cycle  
(for example, water level, drum  
movement, number of rinses, spin  
speed) and the water temperature  
according to type of washing.  
OFF  
Switches the washing machine off;  
at all other positions the machine  
is ON.  
To amend programme settings selected by mistake, turn the programme  
selector to OFF. This restores the original settings.  
COTTONS/LINEN, EASY-CARES  
Wash programme from 20 °C to 95 °C, generally used for all Cottons/  
Coloureds (cotton/linen), Easy-Cares (mixed fibres, for example cotton/  
polyester) and synthetics. The programme is suitable for different fab-  
rics and loads. Once a temperature has been set, the machine will auto-  
matically select a COTTONS/LINEN or EASY-CARES programme as  
appropriate. If there are Easy-Cares only, do not exceed the load weight  
of 2.5 kg, to avoid excessive creasing.  
10  
 
Operating Instructions  
STARCHING  
Separate starching, separate conditioning, separate treatment of  
damp clothes (1 rinse, liquid conditioner is washed in from the æ com-  
partment, spin).  
This can also be selected if a separate rinse is necessary. In this case,  
you do not need to add anything to the compartment.  
DRAIN  
To drain the water after a rinse hold (without spinning).  
The effect of Rinse Hold is that the washing is left to soak in the last  
rinse water; it is not spun.  
3
SPIN  
Draining the water after a Rinse Hold and Spin, or separate spinning of  
hand-washed Cottons/Coloureds and Easy-Cares.  
SHORT SPIN  
Draining the water after a Rinse Hold and Short Spin, or separate Short  
Spin of delicate fabrics (delicates, woollens) at low spin speed.  
DELICATES  
Wash programme for Delicates at 30 °C or 40 °C.  
WOOL / P (Handwash)  
Wash programme (cold, up to 40 °C) for machine-washable wool and  
hand-washable wool items carrying the ï care symbol. (Handwash).  
SILK / P (Handwash)  
Wash programme at 30 °C for hand and machine-washable silk.  
Since silk is a very delicate material, we recommend washing only one  
item at a time (if possible), and never washing together with other,  
rougher fabrics. An even more gentle treatment can be selected for ex-  
tremely delicate silk items, using the TIME SAVER button.  
3
FASHION  
A special care programme at 40 °C, for modern textiles such as Viscose,  
Modal, Cupro, Lyocell, providing gentler handling than the DELICATES  
programme, and a stronger cleaning action than the Handwash pro-  
gramme.  
REFRESH  
A special programme of approx. 20 minutes at a maximum temperature  
of 30 °C for quick washing of items such as sports wear, which have  
been worn once and are only slightly soiled.  
11  
 
Operating Instructions  
EASY IRON  
Wash programme at 40 °C for easy-care items which, after this pro-  
gramme, are to be ironed only lightly or not at all.  
ENERGY SAVING  
2
Special energy and water saving programme at about 60 °C, for lightly  
to normally soiled Cottons/Coloureds (cotton/linen), with extended  
wash time.  
Programme Option Buttons  
The programme option buttons are used to adapt  
the programme to suit the degree of soiling of the  
wash. The additional PRE-WASH and STAIN options  
are not needed for normally soiled washing. The  
different functions can be combined together, de-  
pending on the programme.  
PRE-WASH (Pre-wash/Soaking)  
Cold pre-wash before the main wash cycle, which  
follows automatically. The DELAY TIMER button  
changes Pre-wash to warm soaking.  
SENSITIVE  
Special extra programme function that gives an extra rinse along with  
better fabric care (less drum movement). This is ideal when frequent  
washes are necessary, for example in cases of sensitive skin. RINSE+ can  
still be selected as well.  
STAIN  
For heavily soiled or stained washing. (In-wash stain treatment prod-  
ucts (powder or tablets) are washed in at the optimum time as the pro-  
gramme progresses.)  
With the WOOL/P (Handwash) setting, the additional programme op-  
tion buttons cannot be used.  
3
12  
 
Operating Instructions  
TIME SAVER  
Shortened wash programme for lightly soiled washing, consisting of  
three stages with the COTTONS/LINEN, EASY-CARES programme and  
two stages with the other programmes.  
Length of programmes  
Without  
TIME SAVER  
With TIME SAVER  
Programme  
Button  
pressed  
once  
Button  
pressed  
twice  
COTTONS/LINEN,  
EASYCARES at 60 °C  
119 mins.  
68 mins.  
91 mins.  
52 mins.  
63 mins.  
-
Other programmes,  
for example DELICATES at 30 °C  
Programmable functions  
The programmable functions Extra Rinse (RINSE+), Water Cooling and  
Variomatic Spin are described in the Chapter “What to do if ....  
13  
 
Operating Instructions  
Consumption Values and Programme Times  
The following table gives the values for selected programmes under  
standard conditions. Consumption values depend on the selected pro-  
gramme settings (optional functions), washing type and quantity, water  
pressure, such as water inlet temperature, water hardness, room tem-  
perature or detergent used, etc. The tables do, however, give a helpful  
guide for normal household use.  
Programme Selector  
(Temperature)  
Type of  
Load Water Energy Time in  
material in kg in litres in kWh minutes  
ENERGY SAVER 1)  
Cotton  
Cotton  
Cotton  
Cotton  
6
6
6
6
44  
50  
50  
58  
1.05  
2.05  
1.08  
0.66  
120  
148  
119  
116  
COTTONS/LINEN, EASY-CARES 95  
COTTONS/LINEN, EASY-CARES 60  
COTTONS/LINEN, EASY-CARES 40  
COTTONS/LINEN, EASY-CARES 60  
TIME SAVER (press once) 1)  
Synthetics  
Synthetics  
3
3
3
56  
52  
50  
0.95  
0.55  
0.58  
91  
88  
59  
COTTONS/LINEN, EASY-CARES 40  
TIME SAVER (press once) 1)  
COTTONS/LINEN, EASY-CARES 40  
TIME SAVER (press twice)  
Synthetics  
Synthetics  
DELICATES 30  
3
2
56  
42  
0.36  
0.18  
68  
35  
WOOL / P(Handwash) 30  
1) Note:Programme setting for testing in accordance with or in support of Stand-  
ard EN 60 456 and IEC 60 456.  
Wash Time Display  
The multi-display indicates the estimated du-  
ration, in minutes, of the programme.  
3
These timings are estimates and can vary.  
During the programme countdown, the re-  
maining time can be recalculated due to any of the following:  
incoming water temperature, type and quantity of laundry, out of bal-  
ance spin detection and foam detection.  
14  
 
Operating Instructions  
What does "UPDATE" mean?  
The control system of your washing machine is fully electronic. The  
software which determines this control system can be reprogrammed.  
If a further improvement to washing technology is introduced by AEG,  
then your machine can be updated. The cost of the UPDATE will be ad-  
vised at the time of the request.  
For further information regarding this, please contact the AEG Cus-  
tomer Care Department.  
Anti-flood Aqua Control + Aqua Alarm  
The inlet hose has a mechanical built in safety device. In the event of  
the filling hose failing, the safety device will automatically shut off the  
water supply.  
In the event of a leak within the machine the float switch, which is  
mounted in the base of the appliance, will operate the drain pump and  
an audible signal will be heard  
The system will operate as long as the appliance is connected to the  
mains electricity supply, even if the programme selector is in the off  
position.  
15  
 
Operating Instructions  
Before the first wash  
0
Run a washing programme without laundry (selecting COTTONS/LINEN,  
EASY-CARES 95, with half the normal amount of detergent).  
This removes any residues from the drum which may have been left  
during manufacturing.  
Preparing for a wash cycle  
Sorting and preparing the washing  
Sort the washing according to care symbols (see Section "Types of  
washing and care symbols").  
Empty out the pockets.  
Remove metal objects (such as paper clips, safety pins, etc.).  
To avoid damage and tangling: close zips, button pillow-cases and  
duvet covers, tie together loose tapes and strings (for example on  
aprons).  
Turn items with double-layered fabrics inside out (sleeping bags, ano-  
raks, etc.).  
Knitted coloured fabrics such as woollens and other materials with  
decorations or jewellry should also be turned inside out.  
Wash small, delicate items (such as baby's socks, tights, bras, etc.) in a  
washing net, cushion cover with a zip or in large socks.  
Special care must be taken with net curtains. Remove metal or plastic  
rollers liable to snag or tie the curtains up in a net or bag. We cannot  
accept liability for any damage.  
Coloured and white washing should not be washed together in the  
same cycle. Otherwise, whites can discolour or turn grey.  
New coloured garments often have excess dye. It is better to wash  
these items separately for the first time.  
Mix large items with smaller ones. This gives more effective washing  
and distributes items better during the spin cycle.  
Shake out the washing before loading it into the washing machine.  
Separate items from one another before placing in the drum.  
Pay attention to care advice such as "Wash separately" or "Wash sep-  
arately several times"!  
16  
 
Operating Instructions  
Types of washing and care symbols  
Care symbols help you to choose the correct wash programme.  
Washing should be sorted by type and according to care symbols.  
The temperatures indicated on the care symbols are the maximum wash  
temperatures.  
Cottons ç  
Cotton and linen items with this care symbol are not sensitive to ma-  
chine washing or high temperatures. The COTTONS/LINEN, EASY-CARES  
programme is suitable for this type of washing.  
Coloureds è ë  
Cotton and linen items with this care symbol are not sensitive to ma-  
chine washing. The COTTONS/LINEN, EASY-CARES programme is suita-  
ble for this type of washing.  
Easy-Care washing ê í  
Materials such as fine cotton, cotton-blend fabrics and synthetics with  
these care symbols require a gentler machine wash. The COTTONS/  
LINEN, EASY-CARES and EASY-IRON programmes are suitable for these  
types of washing.  
Delicates ì  
Materials such as layered fibres, microfibres, synthetics and net curtains  
with this care symbol require careful handling. The DELICATES pro-  
gramme is suitable for this types of washing.  
Viscose í ì  
Modern fabrics such as Viscose, Cupro, Lyocell, Modal, etc. need partic-  
ularly careful handling. The FASHION programme is suitable for this  
type of washing.  
Wool, silk and especially sensitive washing 9 ì ï  
Fabrics like wool, wool blends and silk with these care symbols are par-  
ticularly sensitive to machine washing. The WOOL/P (Handwash) and  
SILK/P (Handwash) programmes are suitable for these types of fabrics.  
Important! Materials with the care symbol  
not be washed in the washing machine.  
(Do not wash) should  
ñ
17  
 
Operating Instructions  
Detergents and Conditioners  
Which detergent and conditioner?  
Use only detergents and conditioners which are suitable for use in au-  
tomatic washing machines. Always follow the manufacturer's instruc-  
tions.  
How much detergent and conditioner?  
The required quantity depends upon:  
the extent of soiling of the washing  
the hardness class of the mains water  
the amount of washing  
Should the detergent manufacturer not specify the dosage quantity for  
2
less than full loads, reduce the detergent accordingly: For a half load  
reduce the quantity by 1/3. For a small load or an EASY IRON pro-  
gramme reduce the quantity by 1/2.  
Observe the instructions for use and dosing provided by the detergent  
and conditioner manufacturer.  
Water softening  
For medium to high water hardness (hardness class II upwards) a water  
softening agent can be used. Refer to the manufacturer's instructions.  
Then always add the appropriate amount of detergent (underdosing)  
for hardness class I (soft). Your local Water Authority can advise you on  
the hardness of the water in your area.  
Water hardness details  
Water hardness in °dH  
(German hardness scale)  
Water hardness in ppm  
(Parts Per Million)  
Hardness class  
I - soft  
0 - 7  
7 - 14  
to 125  
125 - 250  
II - medium hard  
III - hard  
14 - 21  
250 - 375  
IV - very hard  
greater than 21  
greater than 375  
18  
 
Operating Instructions  
Running a washing cycle  
Brief instructions  
A washing cycle consists of the following steps:  
01. Set the appropriate washing programme:  
Set the programme and temperature using the programme selector  
Select any programme options if required  
2. Change the Spin Speed/select RINSE HOLD as necessary.  
3. Set the DELAY TIMER as required.  
4. Open the door and load the washing.  
5. Close the door.  
6. Add detergent/conditioner.  
7. Start the washing programme by pressing the START/PAUSE button.  
After the washing programme has ended:  
Important! If the washing cycle has ended with a Rinse Hold, select  
DRAIN, SPIN or SHORT SPIN before opening the door.  
8. Open the door and remove the washing.  
9. To switch off the washing machine, turn the programme selector  
to OFF.  
Setting the wash programme  
See “Programme tables“ for a suitable programme, correct temperature  
and possible options to suit the type of washing.  
3
01. Set the programme selector to  
the desired wash programme  
with the desired temperature.  
The expected duration of the  
programme selected is displayed  
in the multi display in minutes.  
19  
 
Operating Instructions  
2. If required, select the programme option(s). The in-  
dicator display of the selected option lights up.  
To change the option press another button.  
To cancel a selection, press the button again.  
Changing Spin Speed /selecting RINSE  
HOLD  
0
To change Spin Speed for the final spin (if neces-  
sary)/select RINSE HOLD:  
Press the Spin Speed/RINSE HOLD button as often  
as necessary, until the indicator light for the de-  
sired speed (or Rinse Hold) is lit.  
If RINSE HOLD is selected, the washing is left to  
soak in the last rinse water, without spinning.  
If the Spin Speed is not changed, the final spin is automatically ad-  
justed to suit the washing programme:  
3
COTTONS/LINEN, EASY-CARES  
ENERGY SAVING  
DELICATES  
WOOL / P (Handwash)  
SILK/ P (Handwash)  
FASHION  
1400 revolutions per minute  
1400 revolutions per minute  
1200 revolutions per minute  
1200 revolutions per minute  
1200 revolutions per minute  
1200 revolutions per minute  
1200 revolutions per minute  
EASY IRON  
The speed of intermediate spins depends on the selected programme,  
and cannot be changed.  
20  
 
Operating Instructions  
Setting the delay timer/soaking duration  
Delay timer  
The DELAY TIMER button makes it possible to delay the start of a wash  
programme by 1 to a maximum of 19 hours.  
01. Select wash programme.  
2. Press DELAY TIMER button.  
When start delay has been set, the DELAY  
TIMER display lights up.  
Depress the DELAY TIMER button until the  
desired start delay appears, e. g. 12hfor a 12 hour delay to the start of  
the programme. If19his displayed and the button is pressed again,  
then the delay timer is cancelled. The duration of the set wash pro-  
gramme will now appear in the display in minutes, e. g.120.  
The set delay timer can also be cancelled it the programme selector is  
set to the OFF position.  
3. Press START/PAUSE button.  
Soaking duration  
While pressing the PRE WASH button and the DELAY TIMER button,  
the duration of soaking can be increased in hourly steps up to a maxi-  
mum of 19 hours.  
01. Press and hold the PRE WASH button.  
2. Press DELAY TIMER button.  
Soaking is set, the WASH TIME indicator illuminates.  
The soaking time is now increased by 1 hour.  
3. By repeated pressing of the DELAY TIMER button, the soaking times can  
be increased in steps of an hour.  
The WASH TIME and DELAY TIMER displays light up.  
21  
 
Operating Instructions  
Opening and closing the door  
0
0
Open: Press the DOOR button. The door springs open.  
Close: Press the door firmly closed.  
When the unit is switched on, the DOOR display shows  
whether the door can be opened:  
green: The door can be opened (not when programming is acti-  
vated, see the section "Programme protection“ for details)  
off:  
red:  
Door cannot be opened  
Door is open  
Loading the washing  
For maximum loads, see “Programme Tables.  
For hints on how to prepare washing correctly, see "Sorting and prepar-  
ing the washing.  
3
01. Sort and prepare the washing by type and colour.  
2. Open the door: press the DOOR button. The door springs open.  
3. Load the washing.  
Important! Do not trap washing when closing the door. The fabrics and  
the machine could be damaged.  
4. Close the door firmly.  
22  
 
Operating Instructions  
Adding detergent/conditioners  
For instructions concerning detergent and conditioners, see Section  
“Detergents and conditioners.  
3
01. Open the detergent dispenser additives  
drawer : press the flap so as to be able  
to grasp the handle (1), and pull out the  
drawer (2).  
2. Add the detergent/conditioners.  
Compartment for in-wash stain  
treatment powders/tablets  
(for use with the STAIN programme  
option only)  
Compartment for main wash deter-  
gent  
(If you use a water softener and need  
the right-hand compartment for the  
Pre-wash/Soaking agent, add the wa-  
ter softener to this compartment with  
the main wash detergent.)  
Compartment for liquid conditioners  
(softeners, finishers, starch)  
Important! Do not fill the compartment past the  
MAX mark. If required, dilute concentrated fluids up  
to the MAX mark, and dissolve powdered starches.  
Note: A small amount of water remaining in the liquid  
conditioner compartment is normal and does not  
affect the wash results.  
Compartment for Pre-wash detergent/  
Soaking agent  
(for the PRE-WASH/SOAKING programme options only)  
or for water softener  
23  
 
Operating Instructions  
3. Push the detergent dispenser drawer in fully  
If using liquid detergents/tablets:  
3
Add liquid detergent or tablets in the quantity recommended by the  
washing detergent manufacturer. Add liquid detergent with the dosage  
container provided by the detergent manufacturer.  
Starting the wash programme  
01. Check that the water tap is open.  
2. Starting the wash programme: Press the  
START/PAUSE button.  
The wash programme is started or starts after  
the end of the time delay set.  
If the DOOR indicator flashes red when pressing the START/PAUSE but-  
ton, then the door is not properly closed. Press the door firmly closed  
and press the START/PAUSE button again.  
3
If a delay start has been set:  
The delay time set counts down, the remaining time until the start of  
the programme is displayed in the multi display (in hours remaining).  
During this time, you can add washing or change the delay time or  
cancel it.  
Adding washing: Press the START/PAUSE button. The door can be  
opened. Then close the door and press the START/PAUSE button  
again.  
Changing or stopping the delay time: Press the DELAY TIMER button  
until the desired time is displayed; when the duration of the pro-  
gramme is displayed (e. g. 120 minutes) the wash programme starts  
immediately.  
24  
 
Operating Instructions  
Washing Programme Progress  
Programme progress display  
Prior to the start, the programme steps chosen are  
displayed by the Programme progress display.  
During the washing programme the current  
programme step is displayed.  
Multi display  
The expected time remaining (in minutes)  
up to the end of the programme is shown  
in the Multi display.  
The multi display indicates the estimated duration, in minutes, of the  
programme. These timings are estimates and can vary according to in-  
coming water temperature, type and quantity of laundry, out of bal-  
ance spin detection and foam detection. During the programme  
countdown, the remaining time can be recalculated due to any of the  
above factors.  
3
Changing spin speed  
During the washing programme, the spin speed can still be changed or  
RINSE HOLD can be set.  
Other settings cannot be changed.  
Stopping the programme  
Turn the progamme selector to OFF in order to stop the washing  
prematurely.  
0
The programme can be interrupted at any time with the START/PAUSE  
button and can be continued again by pressing this button again.  
3
25  
 
Operating Instructions  
Washing cycle complete/Removing the washing  
Once the wash programme has come to an end the END indicator il-  
luminates on the programme progress display.  
If the EASY IRON programme was selected, and anti-crease phase of  
approximately 30 minutes follows the programme end. Here, the  
multi display shows the remaining time and the END indicator illumi-  
nates. During the anti-creasing phase, the door can be opened at any  
time and the washing can be removed.  
If RINSE HOLD was selected, the display next to the  
START/PAUSE button flashs.  
01. After a rinse hold, the water must first be pumped out:  
Either press the START/PAUSE button (water is pumped out and the  
washing is spun according to the completed programme; using the  
RINSE HOLD spin speed button, it is possible to change the spin speed  
during spinning),  
or  
Turn the programme selector to DRAIN and press the START/PAUSE  
button (the water is pumped off without spinning),  
or  
Turn the programme selector to SPIN or SHORT SPIN and press START/  
PAUSE button (water is pumped out and the washing is spun accord-  
ingly).  
After the end of this programme step, the END display lights up.  
2. Open the door.  
As soon as the indicator next to the DOOR button is green, the door can  
be opened (not if programme security is activated. For details see „Pro-  
gramme security„).  
3. Remove the washing.  
4. Turn the programme selector to OFF.  
5. After washing, pull the washing detergent drawer out a little so that it  
can dry out. Leave the door ajar so that air can circulate in the drum.  
If the OVERDOSING indicator illuminates, then too much  
detergent was used in the washing programme just  
3
completed. Observe the dosing recommendations of the  
detergent manufacturer as well as the load quantity for the next wash.  
Important: If the washing machine is not to be used for a long period:  
Close the water tap and disconnect the washing machine from the  
electricity mains. (Anti-flood: The Aqua Control with Aqua Alarm does  
not function if the power supply is interrupted).  
26  
 
Operating Instructions  
Programme Tables  
Washing  
The tables do not show all the possible settings, only those most likely  
to be selected for everyday purposes.  
Possible  
Max.  
Load  
(Dry weight)1)  
Type of washing,  
Care symbol  
Programme selector  
Temperature [in °C]  
Programme  
options or  
functions  
PRE-WASH  
SENSITIVE  
STAIN  
Cottons/Coloureds2)  
èç  
6kg  
ENERGY SAVING 60  
TIME SAVER  
PRE-WASH  
SENSITIVE  
STAIN  
COTTONS/LINEN, EASY-  
CARES  
20 to 95  
Cottons/Coloureds  
ëèç  
6kg  
3kg  
3kg  
TIME SAVER  
REFRESH 30  
PRE-WASH  
SENSITIVE  
STAIN  
COTTONS/LINEN, EASY-  
CARES  
20 to 60  
TIME SAVER  
Easy-Cares2)  
PRE-WASH  
STAIN  
TIME SAVER  
îí ê  
EASY IRON3) 40  
REFRESH 30  
1kg  
3kg  
3kg  
(or 15-20m2  
net curtains)  
PRE-WASH  
STAIN  
TIME SAVER  
DELICATES 30, 40  
Delicates  
ì
3kg  
2kg  
1kg  
FASHION 40  
Wool/ Handwash  
9 ì ï  
WOOL/PCOLD to 40  
SILK/P30  
Silk/Handwash ï  
TIME SAVER  
1) A 10 litre bucket holds around 2.5kg of dry clothes (cotton).  
2) Programme settings for testing in accordance with or in support of standard EN  
60 456 and IEC 60 456, are described in the Chapter “Consumption Values and  
Programme Times.  
27  
 
Operating Instructions  
3) Creasing can be largely avoided by keeping wash loads under 1kg (roughly 5 to 7  
easy-care men's shirts).  
Separate Rinse/Conditioning/Starching/Treating  
Max. load  
(dry weight)  
Type of washing  
Programme selector  
Cottons/Coloureds  
Wool/Handwash  
6kg  
STARCHING  
STARCHING + TIME SAVER  
button  
2kg  
Separate Spinning  
Max. load  
(dry weight)  
Type of washing  
Programme selector  
Cottons/Coloureds  
Easy-Cares  
Delicates  
6kg  
3kg  
3kg  
2kg  
1kg  
SPIN  
Wool/Handwash  
Silk  
SHORT SPIN  
28  
 
Operating Instructions  
Maintenance and Cleaning  
Control panel  
Important! Do not use household furniture polish or abrasive cleaners  
to clean panel and operating parts.  
0
Wipe over the operating panels with a damp cloth. Use warm water.  
Detergent Dispenser Drawer  
The detergent dispenser drawer should be cleaned from time to time.  
01. Pull the detergent dispenser drawer out as far as it will go.  
2. Remove the detergent dispenser drawer by pulling sharply.  
3. Take the conditioner insert out of the  
middle compartment.  
4. Clean the conditioner insert under  
running water.  
5. Clean the separate compartments  
with warm water. It is best to use  
a flat brush.  
6. Push on the conditioner insert  
as far as it will go so that it is  
securely in place.  
29  
 
Operating Instructions  
7. Use a brush to clean the entire  
compartment area of the washing  
machine, particularly also the  
nozzles on the top side of the  
compartment.  
8. Set the detergent dispensing  
drawer into the guide tracks and  
push it in.  
Washing Machine Drum  
The washing machine drum is made from rust-free stainless steel. Any  
objects left in the laundry which are likely to rust can stain the drum.  
Important! Do not clean the stainless steel drum with descaling agents  
containing acids, scouring agents containing chlorine or iron, or steel  
wool. Your local AEG Service Force Centre has suitable agents available.  
0
Remove any rust stains on the drum using a stainless steel cleaning  
agent.  
Maintenance Wash  
With the use of low temperature washes it is possible to get a build up  
of residues inside the drum.  
3
We recommend that a maintenance wash be performed on a regular  
basis.  
To run a maintenance wash:  
The drum should be empty of laundry.  
01. Select the hottest cotton wash programme.  
2. Use a normal measure of detergent, must be a powder.  
Main door  
0
Regularly check to see if there are deposits or foreign objects in the  
rubber seal behind the door, and remove them.  
30  
 
Operating Instructions  
Cleaning the drain pump  
Paper clips, nails and so on can sometimes get into the washing ma-  
chine with the washing and remain in the drain pump casing. Fluff and  
strands of fabric can gather on these items and block the drain pump.  
Therefore the drain pump should be cleaned at least once a year.  
Warning! Switch off the washing machine and pull out the mains plug  
before cleaning the drain pump.  
1
01. First carry out emergency emptying (see section "Carrying out emer-  
gency emptying“).  
2. Place a towel on the floor in front of the cover of the drain pump.  
Surplus water may flow out.  
3. Unscrew the drain pump cover anti-  
clockwise and pull it out.  
4. Remove any foreign bodies from the  
pump housing.  
5. Replace the cover. Insert the webs on  
the cover laterally into the guide slots  
and screw on the cover securely clock-  
wise.  
6. Close the emergency emptying hose and  
place it in the holder.  
7. Close the flap.  
31  
 
Operating Instructions  
What to do if...  
Trouble Shooting  
If the appliance is not working correctly, please carry out the following  
checks before contacting your local Service Force Centre. Important: If  
you call out an engineer to a fault listed below or to repair a fault  
caused by incorrect use or installation, a charge will be made even if  
the appliance is in guarantee.  
If the fault code C1oder C2is shown in the  
multi-display, you may be able to remedy  
the fault yourself (see the Fault table be-  
low).  
After clearing the fault, press the START/PAUSE button. If the fault  
code is shown again, contact your local Service Force Centre.  
For all other faults displayed in the multi-display, please contact your  
local AEG Service Force Centre, stating the fault code.  
Problem  
Possible cause  
Remedy  
The mains plug is not  
plugged in.  
Plug in the mains plug.  
Replace the fuse.  
The house fuse has blown.  
Door is not properly closed.  
Washing machine does  
not work.  
Close door; Lock must en-  
gage audibly .  
Keep the START/PAUSE but-  
ton pressed until the pro-  
gramme starts.  
START/PAUSE button has not  
been pressed long enough.  
Cancel child safety feature  
(see section „Child safety  
feature“).  
Child safety feature is  
switched On.  
Door cannot be closed.  
Water tap is closed.  
Open water tap.  
Close water tap. Disconnect  
hose from water tap, remove  
filter and clean under  
running water.  
Filter in the socket of the in-  
let hose connection is  
blocked.  
Water is not entering.  
Error code (1 ap-  
pears.  
Water tap is blocked with  
limescale or is faulty.  
Check the water tap and  
have it reaired if necessary.  
32  
 
Operating Instructions  
Problem  
Possible cause  
Remedy  
Remove transport packaging  
according to setting up and  
connection instructions.  
Transport packaging has not  
been removed.  
Adjust the feet according to  
installation and connection  
instructions.  
The machine is not level.  
Washing machine vi-  
brates during operation  
or is unstable.  
There is very little washing in  
the drum (e.g. only a dressing  
gown).  
This does not affect the op-  
eration of the machine.  
Check the drain hose and re-  
move any kink if necessary,  
or clean the drain pump and,  
if necessary, remove foreign  
bodies from the pump hous-  
ing.  
Water could not be fully  
pumped out before spinning  
because the drain hose is  
kinked or water pump is  
blocked.  
If may be necessary to re-  
duce the amount of deter-  
gent used. Follow the  
detergent manufacturer’s  
recommendations.  
Excessive foaming dur- Probably too much detergent  
ing the main wash.  
has been used.  
The screw Connection on the Tighten the inlet hose screw  
inlet hose is leaking.  
connection.  
Check the drain hose and re-  
place it if necessary.  
Drainage hose is leaking.  
The drain pump cover is not  
correctly close.  
Close cover correctly.  
Water leaks out of the  
washing machine.  
Stop the programme, remove  
the washing caught in the  
door. Restart the programme.  
Washing is caught in the  
door.  
Close the emergency empty-  
ing hose (see section „Carry  
out emergency emptying“).  
Call your local Service Force  
Centre if the emergency  
The emergency emptying  
hose is not correctly closed  
or is leaking.  
emptying hose is leaking.  
33  
 
Operating Instructions  
Problem  
Possible cause  
Remedy  
The drain pump runs  
Close the water tap, remove  
constantly - even when The Aqua Control anti-flood the mains plug and inform  
the appliance is  
switched off.  
system has been activated.  
your local Service Force Cen-  
tre.  
Fabric softener was not The insert in the comparti-  
rinsed in, compart- ment for conditioners is not  
ment æfor condition- correctly attached or is  
ers is filled with water. blokked.  
Clean the detergent dis-  
penser drawer and attach the  
conditioner insert correctly.  
Pay attention to the maxi-  
mum load quantity (see pro-  
gramme tables). In the case  
of easy-care fabrics select  
the EASY IRON programme.  
Washing is heavily  
creased.  
Probably too much washing  
has been put in drum.  
Drain hose is kinked.  
Remove the kink.  
Contact your local Service  
Force Centre. For pumping  
heights over 1 m a conver-  
sion kit is available as a spe-  
cial accessory.  
Maximum pump height  
(emptying height 1m from  
base surface of the appli-  
ance) is exceeded.  
The washing is not suf-  
ficiently spun. Water is  
left in the drum.  
Switch off appliance and pull  
out the mains plug. Clean  
the drain pump.  
Error code (2 appears.  
Drain pump is blocked.  
At the siphon connection: Si-  
phon is blocked.  
Clean siphon.  
The door is locked for safety  
reasons (DOOR display is  
OFF).  
Wait until the DOOR display  
lights up green.  
The door cannot be  
opened when appliance  
is switched on.  
Cancel programme security  
(see section „Programme  
protection“).  
The programme security  
function is On.  
Water tap is not fully  
opened.  
Open water tap fully.  
Remnants of detergent  
are building up in the  
detergent drawer.  
Close the water tap. Unscrew  
the inlet pipe from water tap  
and from the appliance and  
clean the filter.  
The inlet hose filter in the  
coupling of the inlet hose at  
the tap is blocked.  
34  
 
Operating Instructions  
Problem  
Possible cause  
Remedy  
The cause is probably a de-  
tergent with a high silicate  
content.  
No negative influence on the  
rinse results, use a liquid de-  
tergent if necessary.  
The rinse water is  
cloudy.  
When pressing a pro-  
gramme option button  
the corresponding dis-  
play does not light up.  
The selected programme op-  
tion cannot be combined  
with the set programme.  
Make another selection.  
Programme security is  
switched On; the pro-  
gramme selector has been  
moved during the wash cy- „Programme security“).  
cle.  
Turn programme selector to  
its original position (see  
Programme cycledis-  
play flashes constantly.  
35  
 
Operating Instructions  
If the washing results are not satisfactory  
If the washing turns greyish and limescale deposits are present in  
the drum  
Insufficient detergent has been added.  
Incorrect detergent was used.  
Stains were not pre-treated.  
Programme or temperature was not set correctly.  
If using modular detergents, the individual components were not  
used in the correct ratio.  
If there are still grey stains on the washing  
Soiled garments with ointments, grease or oils were washed with in-  
sufficient detergent.  
The temperature selected for the wash was too low.  
A frequent cause is that fabric softener - particularly a concentrated  
one - has come into contact with the washing. Wash out these types  
of stains as soon as possible and use the fabric softener carefully.  
If after the last rinse foam is still visible  
Modern detergents can still cause foam in the final rinse cycle. How-  
ever, the washing is still sufficiently rinsed.  
If there are white residues on the washing  
These are insoluble contents of modern detergents. They are not the  
result of an insufficient rinse. Shake out the washing or brush it off.  
Turn the washing inside out before washing it. Review your choice of  
detergent and if necessary use liquid detergent.  
36  
 
Operating Instructions  
Carrying out an emergency emptying  
If the washing machine no longer pumps out the water, emergency  
emptying must be carried out.  
If the washing machine is located in a room in which below freezing  
temperatures might occur, emergency emptying must be carried out.  
Furthermore: unscrew the inlet hose from the water tap and drain off  
the water. Empty the drainage hose.  
Warning! Switch off the washing machine and pull out the mains plug  
prior to performing emergency emptying.  
1
Warning! The water, which flows out of the emergency emptying hose  
can be hot. First allow the water to cool down before you carry out the  
emergency emptying.  
01. Have a flat container on hand to catch the water.  
2. Pull down the flap in the right corner of  
the base strip outwards and pull it off.  
3. Remove the emergency emptying hose  
from its holder.  
4. Place the container under the hose.  
5. Detach the plug of the emergency emp-  
tying hose by turning it anticlockwise  
and pull it out.  
The water runs out. Depending on the  
amount of water, it may be necessary to  
empty the collecting vessel several  
times. To do this, close the emergency  
emptying hose temporarily with the  
plug.  
Discard the water from the container, replace it under the emergency  
emptying hose and remove the plug from the hose.  
37  
 
Operating Instructions  
When the water is completely drained:  
6. Push the plug securely into the emergency emptying hose and turn it  
clockwise to secure it.  
7. Replace the emergency emptying hose in its holder.  
8. Put on the flap and close.  
Emergency unlocking of the door  
If the door cannot be opened, it can be opened using the emergency  
unlock feature.  
Warning! If it is necessary to unlock the door manually, always ensure  
that the washing machine has been disconnected from the electricity  
supply first.  
1
01. If water can be seen in the window of the door, first perform and emer-  
gency emptying (see section "Carry out emergency emptying“).  
2. Pull down the flap in the right hand  
side of the base panel.  
3. Turn the rotary knob clockwise using a  
coin. The door springs open.  
38  
 
Operating Instructions  
Additional rinse cycle (RINSE+)  
The washing machine is set for very economical water consumption.  
However, for people who suffer from allergies to detergents, it can be  
helpful to rinse with extra water.  
If this function is selected, an extra rinse is added to the COTTONS/  
LINEN, EASY-CARES, EASY IRON and DELICATES programmes.  
When delivered, the machine is not set for the additional rinse.  
3
To set the additional rinse:  
01. Turn the programme selector to SHORT SPIN.  
2. Press and hold the SENSITIVE button for at least 5 seconds.  
When the button has been pressed for 5 seconds, RINSE+ flashes on  
the Programme Progress display for 5 seconds.  
3. While RINSE+ is flashing, release the SENSITIVE button.  
When it stops flashing, the additional rinse is set. It remains set until  
cancelled again.  
When the additional rinse has been set, the RINSE+ indicator flashes  
on the display before the programme starts and during the additional  
rinse.  
4. If you want to check whether the additional rinse has been set:  
Turn the programme selector to SHORT SPIN.  
Push the SENSITIVE button briefly.  
If RINSE+ flashes on the Programme Progress display, the additional  
rinse has been set.  
To cancel the additional rinse:  
01. Turn the programme selector to SHORT SPIN.  
2. Press and hold the SENSITIVE button for at least 5 seconds.  
As soon as the button is pressed, RINSE+ flashes on the Programme  
Progress display. After 5 seconds, RINSE+ stops flashing and remains lit  
continuously for another 5 seconds.  
3. While RINSE+ is lit continuously, release the SENSITIVE button.  
When RINSE+ is no longer lit, the additional rinse has been cancelled.  
An additional rinse cycle increases water consumption and the pro-  
gramme duration.  
3
39  
 
Operating Instructions  
Water cooling  
It may be necessary to cool the water before draining, to prevent ther-  
mal damage to the plastic outlet pipes.  
The water is cooled before draining out at the end of the main wash  
(by adding cold water).  
3
(This setting is only available with the COTTONS/LINEN, EASY-CARES  
programmes, with temperatures over 40 °C.)  
When the washing machine is delivered, water cooling is not set, except  
for the SENSITIVE programme option.  
To set the water cooling function:  
01. Turn the programme selector to SHORT SPIN.  
2. Press and hold the PRE-WASH button for at least 5 seconds.  
When the button has been pressed for 5 seconds, MAIN WASH flashes  
on the Programme Progress display for 5 seconds.  
3. While MAIN WASH is flashing, release the PRE-WASH button.  
When it stops flashing, water cooling has been set. The function re-  
mains set until cancelled again.  
4. If you want to check whether water cooling has been set:  
Turn the programme selector to SHORT SPIN.  
Press the PRE-WASH button briefly.  
If MAIN WASH flashes on the Programme Progress display, water cool-  
ing has been set.  
To cancel water cooling:  
01. Turn the programme selector to SHORT SPIN.  
2. Press and hold the PRE-WASH button for at least 5 seconds.  
As soon as the button is pressed, MAIN WASH flashes on the Pro-  
gramme Progress display. After 5 seconds, MAIN WASH stops flashing  
and remains lit continuously for another 5 seconds.  
3. While MAIN WASH is lit continuously, release the PRE-WASH button.  
When MAIN WASH is no longer lit, water cooling has been cancelled.  
The water cooling function raises water consumption and extends pro-  
gramme time.  
3
Additional rinse cycle and water cooling  
You can combine the additional rinse and water cooling functions.  
Set the two functions as described under "Additional rinse cycle" and  
"Water cooling".  
40  
 
Operating Instructions  
Variomatic spin  
The variomatic spin is integrated into the final spin. The washing does  
not cling to the side of the drum as much and can be taken out more  
easily. This can be set with the COTTONS/LINEN, EASY-CARES pro-  
grammes.  
To set Variomatic Spin:  
01. Turn the programme selector to SHORT SPIN.  
2. Press and hold the STAIN button for at least 5 seconds.  
When the button has been pressed for 5 seconds, the END light flashes  
on the Programme Progress display for 5 seconds.  
3. While END is flashing, release the STAIN button. When it stops flashing,  
Variomatic Spin has been set. It remains set until cancelled again.  
4. If you want to check whether Variomatic Spin has been set:  
Turn the programme selector to SHORT SPIN.  
Press the STAIN button briefly.  
If the END light flashes on the display, Variomatic Spin is set.  
To cancel Variomatic Spin:  
01. Turn the programme selector to SHORT SPIN.  
2. Press and hold the STAIN button for at least 5 seconds.  
As soon as the button is pressed, the END light flashes on the Pro-  
gramme Progress display. After 5 seconds, the END light stops flashing  
and remains continuously lit for another 5 seconds.  
3. While END is continuously lit, release the STAIN button. When END is  
no longer lit, Variomatic Spin has been cancelled.  
41  
 
Operating Instructions  
Programme Protection  
To protect a programme setting against unintentional changes or tam-  
pering (for example, programme selector turned or buttons pressed ac-  
cidentally, etc.), set the Programme Protection. This will protect your  
washing from damage.  
The Programme Protection can be set or released at any time while the  
programme is running.  
3
Setting the Programme Protection:  
01. Set the desired programme.  
2. Press the START/PAUSE button to start the programme.  
3. Press and hold the PRE-WASH and SENSITIVE buttons at the same time,  
for around 5 seconds. The programme progress display flashes for  
5 seconds;  
The Programme Protection is now set.  
No other settings can be selected as long as the Programme Protection  
3
is active. The door cannot be opened with the DOOR button. Also, when  
the wash cycle is completed, the Programme Protection must be re-  
leased before the door can be opened.  
If one of the buttons is pressed to try to change the setting while the  
wash programme is running, the programme progress display flashes  
for 5 seconds.  
If the programme selector is turned to try to change the setting, the  
programme progress display flashes until the programme selector is re-  
turned to its original setting. This does not affect the wash cycle.  
The programme selector must be at the original position before the  
Programme Protection can be cancelled.  
3
Cancelling the Programme Protection:  
0
Press and hold the PRE-WASH and SENSITIVE buttons at the same time,  
for around 5 seconds. The programme progress display flashes for  
5 seconds, then remains lit steadily for 5 seconds. The Programme Pro-  
tection is now released.  
42  
 
Operating Instructions  
Child Safety Feature  
If the child safety feature is set,  
the door cannot be closed and no  
washing programme can be  
started.  
Setting the child safety feature  
0
Use a coin to turn the rotary knob  
on the inside of the door clock-  
wise as far as it will go.  
Warning! The rotary knob must  
not be in a vertical position after  
adjustment, otherwise the child  
safety feature is not active. The ro-  
tary knob must project as shown in  
the diagram.  
1
Cancelling the child safety  
feature  
Turn the rotary knob anticlockwise  
as far as it will go.  
0
43  
 
Installation and connection instructions  
Installation and connection instructions  
Installation Safety Precautions  
When moving do not tilt the washing machine onto its front or onto  
its right hand side (viewed from the front). This is to prevent the pos-  
sibility of the electronic components becoming wet.  
Before installation inspect the machine for transport damage. Do not  
connect the appliance if it is damaged - contact your retailer.  
Ensure all packaging and transit bolts/bars have been removed, see  
„Removal of Transit Packaging. Failure to remove transit bolts/bars  
may cause serious damage to the appliance or property.  
Always insert the plug into a correctly installed earthed socket.  
Any plumbing work required to install this appliance should be  
carried out by a plumber or competent person.  
Check that the electricity supply is the same as that indicated on the  
appliance´s rating plate.  
Any electrical work required to install this appliance should be carried  
out by an electrician or competent person.  
44  
 
Installation and connection instructions  
Installation of the appliance  
Transporting the appliance  
Do not place the washing machine on its front or on its right hand  
side (viewed from the front). This is to prevent the possibility of the  
electronic components becoming wet.  
Never transport the unit without the transport packaging and bolts/  
bars. Do not remove the transport packaging until the appliance is at  
the installation location. Transporting the unit without the transport  
packaging can damage it.  
Never lift the appliance by the door.  
When transporting the unit with a sack trolley:  
Attach the sack trolley only at the side. The shovel of the sack trolley  
must not be longer than 24 cm, otherwise the float switch can be de-  
stroyed.  
Remove transport packaging  
Important! It is essential to re-  
move the transport packaging be-  
fore putting the appliance into  
operation. Keep all parts of the  
transport packaging in a safe  
place for future use.  
01. Open both hose holders on the  
appliance's rear side and remove  
the hoses and mains cable.  
2. Pull both hose holders off the ap-  
pliance with a strong pull.  
45  
 
Installation and connection instructions  
The special spanner (A) and the  
caps (B) (2 each) and (C) (1 each)  
are supplied with it.  
3
3. Remove the screw D, including  
the compression spring with the  
special spanner A.  
4. Cover the hole with the cap C.  
Important! When fitting the  
plastic caps, press until they snap  
into the rear panel securely.  
5. Remove the two screws (E) with  
the special spanner (A).  
6. Remove the 4 screws (F).  
7. Remove the transit bar (G).  
8. Screw the 4 screws (F) back in for  
safe keeping.  
9. Close the 2 large holes with the  
caps (B).  
Important! When fitting the  
plastic caps, press until they snap  
into the rear panel securely.  
46  
 
Installation and connection instructions  
Installation-Site preparation  
The installation surface must be clean, dry and level. Do not install on  
a deep pile carpet.  
Minor unevenness of the floor surface should never be levelled out by  
laying pieces of wood, card or similar materials, but should always be  
compensated for by adjusting the screw feet.  
If the appliance is installed next to a heat source (e.g. cooking appli-  
ance), a heat insulating pad (87 x 57 cm) must be placed between the  
appliance and the heat source.  
Do not install the appliance in locations where the temperature may  
fall below freezing.  
Please ensure that when the appliance is installed it is easily accessi-  
ble for the engineer in the event of a breakdown.  
Installation on a Suspended Floor  
Suspended wooden floors are particularly susceptible to vibration. To  
help prevent vibration we recommend you place a waterproof wood  
panel, at least 15 mm thick under the appliance, secured to at least  
2 floor beams with screws. If possible install the appliance in one of the  
corners of the room, where the floor is more stable.  
47  
 
Installation and connection instructions  
Levelling the appliance  
Self adjusting foot: The rear foot of your washing machine is designed  
like a spring leg. This makes the machine very stable even at high spin  
speeds.  
3
If the washing machine is still not stable during spinning, proceed as  
follows:  
01. Set the three adjustable feet to  
the nominal value of 10 mm.  
Use the supplied spanner.  
If the self adjusting foot does  
not reach the floor:  
2. Manually extend the self  
adjusting foot (rear left) to  
the required length.  
3. Check the appliance is level using  
a spirit level.  
Important! Never use strips or  
shims of wood or cardboard etc.  
to compensate for any uneven-  
ness in the floor. Always use  
the adjustable feet.  
48  
 
Installation and connection instructions  
Electrical Connection  
Any electrical work required to install this appliance should be carried  
out by a qualified electrician or competent person.  
WARNING - THIS APPLIANCE MUST BE EARTHED.  
The manufacturer declines any liability should these safety  
measures not be observed.  
1
Before switching on, make sure  
the electricity supply voltage is  
the same as that indicated on the  
appliance rating plate.  
The rating plate is located at the  
top of the rim of the open door.  
The appliance is supplied with a  
13amp plug fitted. In the event of  
having to change the fuse in the  
plug supplied, a 13amp ASTA ap-  
proved (BS 1362) fuse must be used.  
Should the plug need to be replaced  
for any reason, proceed as described  
below.  
Green & Yellow  
The wires in the mains lead are  
coloured in accordance with the  
following code:  
Brown  
Blue  
Green and Yellow: Earth  
Blue:  
Brown:  
Neutral  
Live  
Cord Clamp  
The wire coloured green and yellow must be connected to the termi-  
nal marked with the letter “E“ or by the earth symbol  
green and yellow.  
or coloured  
The wire coloured blue must be connected to the terminal “N“ or  
coloured black.  
The wire coloured brown must be connected to the terminal marked  
“L“ or coloured red.  
Upon completion there must be no cut, or stray strands of wire  
present and the cord clamp must be secure over the outer sheath.  
WARNING! A cut off plug inserted into a 13 amp socket is a  
serious safety (shock) hazard. Ensure that the cut off plug is  
disposed of safely.  
1
49  
 
Installation and connection instructions  
Permanent Connection  
In the case of a permanent connection it is necessary that you install a  
double pole switch between the appliance and the electricity supply  
(mains), with a minimum gap of 3 mm between the switch contacts  
and of a type suitable for the required load in compliance with the  
current electrical regulations.  
The switch must not break the yellow and green earth cable at any  
point.  
This appliance is in accordance with the following EU Guidelines:  
Low Voltage Guidelines 73/23 EEC dated 19 February 1973, include  
Guideline Change Notice 93/68 EEC  
;
EMC Guideline 89/336 EEC dated 3 May 1989, including Guideline  
Change Notice 92/31 EEC.  
This appliance complies with the requirements laid out in the EEC Di-  
rective 76/899.  
Voltage 240 V AC: Fuse rating 13 amps  
See rating plate for further information.  
This appliance meets VDE requirements.  
Particular regulations of local electricity authorities must be observed.  
This appliance conforms to EEC Directive No. 82/499/EWG on radio in-  
terference.  
WARNING! Repairs to electrical appliances must only be carried out by  
trained personnel. Improper repairs may lead to serious risks for the  
user.  
1
50  
 
Installation and connection instructions  
Water connection  
The washing machine is provided with safety devices preventing back-  
contamination of the water supply and complies with local water au-  
thority requirements.  
3
This appliance is designed to be permanently plumbed into your home’s  
water supply.  
Before connecting up the machine to new pipework or to pipework  
that has not been used for some time, run off a reasonable amount of  
water to flush out any debris that may have collected in the pipes.  
Important!  
Appliances for connecting to cold water must not be connected to  
hot water.  
Only use new hose sets for the connection.  
Water pressure  
The appliance is designed to operate within the following water  
pressure units. Minimum 1 bar (= 10N/cm2 = 0.1 Mpa), maximum  
10 bar (= 100N/cm2 = 1 Mpa).  
If more than 10 bar: Install a pressure-reduction valve upstream  
If less than 1 bar: Unscrew the inlet hose from the appliance at the  
inlet solenoid valve and remove the flow regulator (to do this, remove  
the filter with needle nose pliers and remove the rubber washer be-  
hind the filter). Replace the filter.  
51  
 
Installation and connection instructions  
Inlet Hose Connection  
A pressure hose 1.5m in length is supplied.  
If a longer inflow hose is required, only a VDE-approved, complete set  
of hoses with fitted hose screw connections offered by your local Serv-  
ice Force Centre is permissible.  
Hose sets in lengths of 2.2m, 3.5m and 5m are available for washing  
machines without Aqua Control.  
Hose sets in lengths of 2.0m, 2.9m and 3.9m are available for wash-  
ing machines with Aqua Control.  
Important! Never cut hoses into pieces in order to extend them!  
Sealing rings are supplied either in the plastic  
nuts of the hose screw connection or in the  
enclosed pack. Do not use other seals!  
3
01. Connect the hose with the angled  
connection to the machine.  
Important!  
Do not lay the inlet hose verti-  
cally downwards. Instead, turn  
it to the right or left as shown  
in the diagram.  
Tighten firmly to prevent  
leakage but do not use  
excessive force.  
2. Connect the hose with a straight connection to a  
water tap with a screw thread R 3/4 (inches).  
Important! Only tighten the screw connection  
manually.  
3. By slowly opening the water tap before putting  
the washing machine into operation it is possible  
to check that the connection is free of leaks.  
52  
 
Installation and connection instructions  
Water Drainage  
The appliance drain hose should hook into a standpipe, the hook in the  
drain hose is formed using the plastic “U-Piece“ supplied. The standpipe  
should have an internal diameter of approximately 38 mm (see dia-  
gram) thus ensuring there is an air break between the drain hose and  
standpipe.  
Important! It is essential to lay  
the drainage hose without kinks.  
When discharging into a stand-  
pipe ensure that the top of the  
curve in the hose end is no more  
than 90 cm (35.4’’) and no less  
than 60 cm (23.6’’) above floor  
level.  
The upright standpipe should  
have a minimum, length of  
30 cm (12’’) from the bottom of  
the elbow to the top of the pipe  
(see diagram). Make sure that it is  
designed in such a way that the  
end of the drain hose cannot be  
covered with water.  
Longer drain hoses are available  
in lengths of 2.7 and 4 metres  
from your AEG Service Force  
Centre.  
53  
 
Installation and connection instructions  
If you intend the drain hose from  
the washing machine to empty  
into a sink, make sure that the  
sink is empty and the plug hose  
is not blocked. Use the plastic  
“U-Piece“ supplied.  
Important! The end of the  
drainage hose must not be  
submerged in the pumped-out  
water. Otherwise, the water  
could be sucked back into the ap-  
pliance.  
Pump head of greater than 1m  
Every washing machine includes a wash water pump for the removal of  
wash and rinse water, which can pump fluids through the outlet hose  
up to a height of 1m, measured from the surface on which the machine  
stands.  
For pump heads of greater than 1m please contact your local  
AEG Service Force Centre.  
54  
 
Installation and connection instructions  
Technical Data  
Height adjustment  
Load (depending on programme)  
of about +10/-5mm  
up to 6kg  
Area of use  
Domestic  
Drum spin speed  
Water pressure  
see Rating Plate  
1-10bar  
(=10–100N/cm2 = 0.1–1.0MPa)  
Dimensions  
(dimensions in mm)  
55  
 
Warranty conditions  
Warranty conditions  
Great Britain  
Guarantee Conditions  
AEG offer the following guarantee to the first purchaser of this appliance.  
1. The guarantee is valid for 12 months commencing when the appliance is handed over  
to the first retail purchaser, which must be verified by purchase invoice or similar docu-  
mentation.  
The guarantee does not cover commercial use.  
2. The guarantee covers all parts or components which fail due to faulty workmanship or  
faulty materials. The guarantee does not cover appliances where defects or poor per-  
formance are due to misuse, accidental damage, neglect, faulty installation,  
unauthorised modification or attempted repair, commercial use or failure to observe  
requirements and recommendations set out in the instruction book.  
This guarantee does not cover such parts as light bulbs, removable glassware or plastic,  
dust bags or filters.  
3. Should guarantee repairs be necessary the purchaser must inform the nearest customer  
service office (manufacturer´s service or authorised agent). AEG reserves the right to  
stipulate the place of the repair (i. e. the customer´s home, place of installation or AEG  
workshop).  
4. The guarantee or free replacement includes both labour and materials.  
5. Repairs carried out under guarantee do not extend the guarantee period for the appli-  
ance. Parts removed during guarantee repairs become the property of AEG.  
6. The purchaser´s statutory rights are not affected by this guarantee.  
European Guarantee  
If you should move to another country within Europe then your guarantee moves with  
you to your new home subject to the following qualifications:  
The guarantee starts from the date you first purchased your product.  
The guarantee is for the same period and to the same extent for labour and parts as  
exist in the new country of use for this brand or range of products.  
This guarantee relates to you and connot be transferred to another user.  
Your new home is within the European Community (EC) or European Free Trade Area.  
The product is installed and used in accordance with our instructions and is only used  
domestically, i. e. a normal household.  
The product is installed taking into account regulations in your new country.  
Before you move please contact your nearest Customer Care Centre, listed below, to  
give them details of your new home. They will then ensure that the local Service Organ-  
isation is aware of your move and able to look after you and your appliances.  
France  
Germany  
Italy  
Senlis  
+33 (0) 44 62 29 29  
+49 (0) 800 234 7378  
+39 (0) 800 117511  
+46 (0) 8 672 5360  
+44 (0) 1753 219899  
Nürnberg  
Pordenone  
Stockholm  
Slough  
Sweden  
UK  
56  
 
57  
 
Index  
Index  
Over-dosed . . . . . . . . . . . . . . . . . . . . . . . . . .26  
A
Aqua Control . . . . . . . . . . . . . . . . . . . . .15, 26  
P
Automatic adjustment foot . . . . . . . . . .9, 48  
C
Pre-wash . . . . . . . . . . . . . . . . . . . . .12, 23, 27  
Pre-wash detergent . . . . . . . . . . . . . . . . 9, 23  
Programme option buttons . . . . . . . . 12, 27  
Programme progress display . . . . . . . . . . . .10  
Programme protection . . . . . . . . . . . . 22, 42  
Pump out . . . . . . . . . . . . . . . . . . . . . . . 11, 26  
Child safety feature . . . . . . . . . . . . . . .32, 43  
Circulation pump . . . . . . . . . . . . . . . . . .9, 31  
Coloureds . . . . . . . . . . . . . . . . . . . . 17, 27, 28  
Conditioner . . . . . . . . . . . . . . . .9, 18, 19, 23  
Conditioning . . . . . . . . . . . . . . . . . . . . .11, 28  
Correcting the programme . . . . . . . . . . . . 10  
Cottons . . . . . . . . . . . . . . . . . . . . . . 17, 27, 28  
Cottons/Linen, Easy-Cares . . . . . . . . . .10, 27  
Customer Service . . . . . . . . . .15, 30, 32, 59  
R
Rating plate . . . . . . . . . . . . . . . 9, 49, 50, 59  
Refresh . . . . . . . . . . . . . . . . . . . . . . . . . 11, 27  
Rinse hold . . . . . . . . . . . . . . . . . . . .11, 20, 26  
Rinse+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39  
Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28  
Risk of frost . . . . . . . . . . . . . . . . . . . . . . 6, 37  
D
Delay timer . . . . . . . . . . . . . . . . . . 10, 12, 21  
Delicates . . . . . . . . . . . . . . . . . . . . . 11, 17, 27  
Detergent . . . . . . . . . . . . . . . . . .9, 18, 19, 24  
Detergent dispenser drawer . . . . . . . . . .9, 23  
S
Sensitive . . . . . . . . . . . . . . . . . . . . . . . . . . . .12  
Service & Spare Parts . . . . . . . . . . . . . . . . .59  
Short Spin . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
Silk . . . . . . . . . . . . . . . . . . . . . . . . . .11, 17, 27  
Soaking . . . . . . . . . . . . . . . . . . . . . . . . . 12, 21  
Soaking agent . . . . . . . . . . . . . . . . . . . . . . .23  
Softener . . . . . . . . . . . . . . . . . . . . . . . 8, 9, 23  
Spin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 25  
Spinning . . . . . . . . . . . . . . . . . 11, 19, 20, 28  
Stain . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 27  
Stain removers . . . . . . . . . . . . . . . . . . . . . . . .9  
Starching . . . . . . . . . . . . . . . . . . . . . . . . 11, 28  
E
Easy Iron . . . . . . . . . . . . . . . . . . . . . . . .12, 27  
Easy-Cares . . . . . . . . . . . . . . . . . . . . . . .17, 27  
Emergency emptying . . . . . . . . . . . . . . . . . 37  
Emergency unlocking . . . . . . . . . . . . . . . . . 38  
Energy Saving programme . . . . . . . . . .12, 27  
F
Fashion . . . . . . . . . . . . . . . . . . . . . . . . . .11, 27  
H
Handwash . . . . . . . . . . . . . . . . . . . . . . .11, 27  
T
Handwashable  
Time Saver . . . . . . . . . . . . . . . . . . . . . . . 13, 27  
silk . . . . . . . . . . . . . . . . . . . . . . . . . . .11, 27  
wool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
U
update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15  
I
W
In-wash stain treatment products . . . . . . 23  
Warranty . . . . . . . . . . . . . . . . . . . . . .6, 32, 56  
Wash time . . . . . . . . . . . . . . . . . . . . . . . . . . .14  
Water  
hardness . . . . . . . . . . . . . . . . . . . . . . . 8, 18  
pumping out . . . . . . . . . . . . . . . . . . . . . . .26  
softener . . . . . . . . . . . . . . . . . . 8, 9, 18, 23  
Water cooling . . . . . . . . . . . . . . . . . . . . . . . .40  
Wool . . . . . . . . . . . . . . . . . . . . . . . .11, 17, 27  
L
Linen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Load . . . . . . . . . . . . . . . . . . . . . . . . . . . .14, 27  
M
Multi-display . . . . . . . . . . . . . . . . . 10, 32, 59  
N
Net curtains . . . . . . . . . . . . . . . . . . . . . . . . . 16  
O
Opening the door . . . . . . . . . .22, 26, 38, 42  
58  
 
Service & Spare Parts  
Service & Spare Parts  
If after carrying out the necessary checks there is still a fault with your  
appliance please contact your local AEG Service Force Centre.  
In guarantee customers should ensure that the suggested checks  
have been made as the engineer will make a charge if the fault is  
not a mechanical or electrical breakdown.  
Please note that proof of purchase is required for in-guarantee service  
calls.  
Service & Spare Parts  
If you require a service engineer or wish to purchase spare parts,  
contact your local AEG Service Force Centre, by telephoning:  
0870 5 929 929  
Help us to help you  
Please determine your type of enquiry before telephoning. When you  
contact us we need to know:  
1. Your name, address, post code and your telephone number.  
2. Clear and concise details of the fault.  
What is the fault?  
When does the fault occur?  
Does the multi-display issue an error-message?  
3. The model, production number and product identification number.  
4. Date of purchase.  
This information can be found on  
the rating plate, so you have these  
numbers to hand we recommend  
you write them below.  
PNC .....................................................  
S-No. .....................................................  
Customer Care  
For general enquiries regarding your AEG appliance, or further infor-  
mation on AEG products please contact our customer care department  
by letter or telephone at the address below or visit our website at  
Customer Care Department  
AEG Domestic Appliances  
55-77 High Street, Slough, Berkshire SL1 1DZ  
Tel: 08705 350350*  
*Calls to this number may be recorded for training purposes.  
59  
 
AEG Hausgeräte GmbH  
Postfach 1036  
D-90327 Nürnberg  
© Copyright by AEG  
822 943 280-01-240502-01  
Subject to change without notice  
 

3Com Switch 3CNJ100 User Manual
3Com Telephone V7000 User Manual
Accusplit Fitness Electronics 1640M4 User Manual
AEG Refrigerator 3150 7 KG User Manual
AMX Stereo Amplifier AVB DA RGBHV ST 0102 User Manual
AOC Marine Instruments E1659FWU User Manual
Aspen Touch Solutions Car Video System SW601532 User Manual
Atlona TV Cables AT COMP300SR User Manual
Axis Communications Security Camera IP Surveillance User Manual
Baracoda Barcode Reader L User Manual