ATN 4X12
°
S.W.A.T. RIFLESCOPE
u s e r ` s g u i d e
AMERICAN
TECHNOLOGIES
NETWORK
CORP.
APPLICATION
Intended for tactical LE and military
marksmen the revolutionary ATN Super
Wide Angle Tactical (SWAT) Scope is
designed and made for professional fire-
arms such as the AR15, M16 and M4.
Leupold Mark4 CQ/T does not even enter
the competition.
The Swat scope also has an abundance
of features like an illuminated reticle with
12 settings to match any light conditions
without overwhelming your natural low-
light vision (reticle is visible when not illu-
minated i.e. no batteries required).
One of the most desired parameters for
a tactical scope is the Apparent Field of
View (Magnification X FOV in degrees)
for fast target acquisition and tracking of
moving targets. Taking the AFV concept
further than Trijicon ACOG (3.5x7=24.5)
and Elcan (3.5x8=28) the ATN SWAT
Scope has an AFV of 4x12=48(!) and the
Combining the strengths of an illuminated
reticle sight with an unparalleled field of
view the SWAT scope is perfect for tactical
situations.
FEATURES
• Magnification: Fixed 4X.
• Objective Aperture: 30mm.
• Adjustment: 1/8 MOA “positive click”
increments;
- with 950 clicks, 9.5 revolutions with 100
clicks per revolution and 120 MOA of total
elevation adjustment;
- with 475 clicks, 4.75 revolutions with 100
clicks per revolution and 60 MOA of total
elevation.
• Power source: 3V; standard watch bat-
tery type CR2032 or CR2432; with mini-
mum 100 hours of continuous use.
Construction/Materials:
Composite
structure using aircraft aluminum alloy,
high-carbon steel alloy and titanium
inserts with 2mm wall minimum.
• Optics: Highest grade heavy glass; all
elements and surfaces are multicoated;
developed with latest optical software and
manufactured with topmost tolerances for
high resolution sharp clear image.
• Reticle: Tactical Ring and Dot reticle
(very quick up close, and the four power
magnification is useful at longer range);
Illuminated with 12 rheostat positions; visi-
ble and operational if illumination is turned
off; standard side locking mechanism.
• Length: 9” (227mm).
• Weight: 36.4oz (1.1 kilo) with built-in
mounting system.
• Sunshade: Standard built-in.
• Front Lens Cover: Included.
• Mounting system: Built-in monorail
with ejection cavity and thumb-screws
for tool-less mounting to MIL-STD-1913
rail bases.
• Environment: waterproof up to 66 feet
(20 meters) up to 1 hour; fog-proof and
nitrogen purged.
• Added Survivability: Built-in standard
adjustable Iron Backup Sights for back-up
emergency operation.
• Point of impact: Always on the center of
the field of view.
• Field of View @ 4X: 12o
- 63ft at 100 yards (21 meters at 100
meters),
- 315ft at 500 yards (105 meters at 500
meters).
• Exit Pupil @ 4X: 7.5mm.
• Eye Relief: 2” (50mm); specialized eye
relief optimized for M16 variant cheek weld
(allows to mount the scope in the conven-
tional middle receiver position).
• Operational Extendibility: 2” Picatinny
rail for additional lighting, laser and other
mission critical tools.
• Diopter Adjustment: +5/- 5; Adjustable
Diopter Eyepiece system.
2
OPERATING
MOUNTING
NOTE: If the rail is not taken out easily,
screw up tight one of screws into the
threaded aperture in the middle of a fixing
projection of the rail. Continue rotation of
the screw. Thus the screw will push out a
rail from a groove.
1. Slightly loosen the fixing screws on the
weaver rail built into the scope.
2. Place the scope on the dovetail mount
of the fire arm making certain that the
mount aligns with the receptor attach-
ment screw groove. Adjust as neces-
sary.
FOCUSING
While holding the scope about two inches
from your eye, quickly glance through the
eyepiece at a featureless, flatly lit bright
area such as a wall or the sky.
3. Tighten the fixing screws.
NOTE: Receptor attachment screws may
need to be tightened after continuous
shooting.
CAUTION: Viewing the sun can cause
serious eye injury, never look at the sun
with this product or even the naked eye.
The ATN Mounting System allows to
change the position of the riflescope flex-
ibly on the weapon in relation to a shooter
If the reticle is not sharply defined
instantly, turn the eyepiece (either direc-
tion) a few turns.
Screws
Rail
Quickly glance through the scope again.
If the focus has improved, but is still not
perfect, continue focusing. If the focus
condition become worse turn the focus
the opposite direction.
LOCKING MECHANISM
Fixing
projection aperture
Threaded
There is a locking mechanism with fixa-
tion screw for windage/elevation adjust-
ment and zeroing mechanism.
by 1/3 of inch. Such positions are addi-
tional to the fixed positions already avail-
able on the weaver rail. For this purpose in
the base of the mounting bracket there is a
rail with a fixing projection. For doing this
one needs to about-face the rail.
To change the position of the riflescope
on the weaver rail additionally follow the
steps mentioned below:
Fixation screw of
locking mechanism
1. Unscrew the two screws, which attach
the rail to the mounting bracket.
Slightly loosen the fixation screw before
zeroing or windage/elevation adjustment.
2. Take the rail out of the groove.
After zeroimg or
windage/elevation
3. About-face the rail in case of neces-
sity.
adjustment turn the fixation screw clock-
wise, to lock the adjustment mechanism.
4. Place the rail into another groove.
5. Fix the rail with the two screws.
3
WINDAGE AND ELEVATION
Remove the dust caps from the top of the
windage and elevation adjusting handles.
The vertical and horizontal adjustments
for the ATN 4X12° SWAT can be achieved
by turning the elevation and windage
adjustment mechanisms (remove dust
caps first). Each click equals to 1/8 inches
Turn the windage and elevation handles
through the number of clicks necessary
for an amendment.
NOTE: Each click of adjustment changes
bullet strike by the amount shown on the
chart below.
Elevation
Windage/Elevation
(inches of movement per click)
100 Yards - 1/8”
200 Yards - 1/4”
300 Yards - 3/8”
400 Yards - 1/2”
500 Yards - 5/8”
When you have finished adjustment of
fire, recap windage and elevation mecha-
nisms.
Windage
Dust caps
at 100 yards. When reaching the maxi-
mum of rotation do not use force.
ELECTRONIC RETICLE
Your scope has an electronic Tacti-
cal Ring and Dot reticle. There are 11
degrees of illumination. The rheostat is
the knob located at the back of the scope.
It is labeled with numbers OFF through 11.
When the rheostat is set at OFF you will
see a black etched reticle. The reticle will
light up red electronically as you rotate the
rheostat through the numbers, 11 being
the brightest.
ZEROING
Pre-zeroing is recommended and can be
done in accordance with a scope guide or
owner’s instructions.
CAUTION: Be sure gun is not loaded.
Always use safe gun handling proce-
dures.
All shooting should be done at an
approved range or other safe area. Eye
and ear protection is recommended.
DANGER: If you used a bore-obstruct-
ing device, remove it before proceed-
ing. If the barrel has-been drilled for
a mount, check that the screws do
not protrude into the bore. Do not fire
live or even blank ammunition with
an obstructed barrel. An obstruction
can cause serious damage to the gun
and possible injury to you and others
nearby.
70 MOA
2 MOA
From a steady position, fire three rounds
at a target. Observe the impact errors
and estimate the correction value. Adjust
windage and elevation handles as needed
to correct aim.
4
ADDED SURVIVABILITY
Iron Backup Sights for back-up
emergency operation
ATN 4X12° SWAT has a built-in visible
flip-up Iron Backup Sights for back-up
emergency operation. Upright the iron
sights for shooting without optic of scope.
The back-side sight has a horizontal and
vertical adjustment.
MAINTAINING YOUR RIFLE SCOPE
Your rifle scope is waterproof and shock-
proof. However, you should never try to
take apart or clean it internally (it will void
your warranty). If your scope ever does
need repairs or adjustments, it should
be returned to ATN’s service department.
The exposed optical surfaces will perform
their best if they are occasionally wiped
clean with a lens cloth or with optical qual-
ity lens paper like those for eyeglasses
or camera lenses. Maintain the metal
surfaces of your rifle scope by removing
any dirt or sand with a soft brush so as to
avoid scratching the finish. Wipe down the
scope with a damp cloth and follow with a
dry cloth. Finally, going over the tube with
a silicone treated cloth will restore luster
and protect the scope against corrosion.
Be careful not to touch the any of the
lenses with the silicone cloth.
5
WARRANTY
LIMITATION OF LIABILITY
LIFETIME LIMITED PRODUCT
WARRANTY
ATN will not be liable for any claims, actions,
suits, proceedings, costs, expenses, damages
or liabilities arising out of the use of this prod-
uct. Operation and use of the product are the
sole responsibility of the Customer. ATN’s sole
undertaking is limited to providing the products
and services outlined herein in accordance with
the terms and conditions of this Agreement.
The provision of products sold and services
performed by ATN to the Customer shall not
be interpreted, construed. 01 regarded, either
expressly or implied. as being fur the benefit of or
creating any obligation toward any third party of
legal entity outside ATN and the Customer: ATN’s
obligations under this Agreement extend solely to
the Customer. ATN’S LIABILITY HEREUNDER
FOR DAMAGES. REGARDLESS OF THE FORM
OR ACTION, SHALL NOT EXCEED THE FEES
OR OTHER CHARGES PAID TO ATN BY THE
CUSTOMER OR CUSTOMER’S DEALER. ATN
SHALL NOT, IN ANY EVENT, BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL. OR CONSE-
QUENTIAL DAMAGES. INCLUDING. BUT NOT
LIMITED TO. LOST INCOME, LOST REVENUE.
OR LOST PROFIT. WHETHER SUCH DAMAGES
WERE FORESEEABLE OR NOT AT THE TIME
OF PURCHASE. AND WHETHER OR NOT
SUCH DAMAGES ARISE OUT OF A BREACH
OF WARRANTY, A BREACH OF AGREEMENT,
NEGLIGENCE, STRICT LIABILITY OR ANY
OTHER THEORY OF LIABILITY.
This product comes with a Lifetime Guarantee
against defects in both materials and workman-
ship. In the event a defect that is covered by the
foregoing warranty occurs during the applicable
period stated above, ATN, at its option, will either
repair or replace the product, and such action on
the part of ATN shall be the full extent of ATN’s
liability, and the Customer’s sole and exclusive
remedy. This warranty does not cover a product
(a) used in other than its normal and customary
manner; (b) subjected to misuse, (c) subjected
to alterations, modifications or repairs by the
Customer of by any party other than ATN without
prior written consent of ATN; (d) special order or
“close-out” merchandise or merchandise sold
“as-is” by either ATN or the ATN dealer; or (e)
merchandise that has been discontinued by the
manufacturer and either parts or replacement
units are not available due to reasons beyond
the control of ATN. ATN shall not be responsible
for any defects or damage that in ATN’s opinion
is a result from the mishandling, abuse, misuse,
improper storage or improper operation, including
use in conjunction with equipment which is elec-
trically or mechanically incompatible with or of
inferior quality to the product, as well as failure to
maintain the environmental conditions specified
by the manufacturer. This warranty is extended
only to the original purchaser. Any breach of this
warranty shall be waived unless the customer
notifies ATN at the address noted below within in
the applicable warranty period.
PRODUCT WARRANTY REGISTRATION
In order to validate the warranty on your product,
ATN must receive a completed Product Warranty
Registration Card for each unit. Please complete
me form below and immediately mail it to our
Service Centre: ATN Corporation, 20 South
Linden Ave. Suite 1B, South San Francisco,
CA 94080. Products qualifying for warranty repair
will be either repaired or replaced within 10 busi-
ness days of receipt of merchandise unless the
customer is notified otherwise.
THE CUSTOMER UNDERSTANDS AND
AGREES THAT EXCEPT FOR THE FOREGOING
WARRANTY, NO OTHER WARRANTIES WRIT-
TEN OR ORAL, STATUTORY, EXPRESSED
OR IMPLIED, INCLUDING ANY IMPLIED WAR-
RANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, SHALL APPLY
TO THE PRODUCT. ALL SUCH IMPLIED WAR-
RANTIES ARE HEREBY AND EXPRESSLY
DISCLAIMED.
OBTAINLNG WARRANTY SERVICE
To obtain warranty service on your unit, take or
send the product, postage paid, with a copy of our
sales receipt to our service centre, ATN Corpora-
tion at the address noted above. All merchandise
must be fully insured with the correct postage;
ATN will not be responsible for improper post-
age, or, missing or damaged merchandise during
shipment.
6
For customer service and technical support, please contact
American Technologies Network Corp.
North American Office
20 S. Linden Ave. Suite 1B, South San Francisco, CA 94080
phone: 800-910-2862, 650-875-0130; fax: 650-875-0129
European Office
phone: 44(0)870-0111286, fax: 44(0) 845-3349142
The following countries can use our
toll free number 00 800 9102-8620
Austria, France, Germany, Holland, Italy, Spain, Sweden, Switzerland
©2003 ATN Corporation
|