American Standard Hot Tub 2422L LA V VA User Manual

INSTALLATION GUIDE FOR  
LIFETIME™ / EVOLUTION™  
WHIRLPOOLS AND BATHTUBS  
MODEL 2422L / LA / V / VA  
5' x 32"  
MODEL 6060L / V  
CORNER  
MODEL 2771L / LA / V / VA  
MODEL 2645L / LA / V / VA  
MODEL 7236L / LA / V / VA  
MODEL 2425L / V - LHO  
MODEL 2425L / V - RHO  
MODEL 2901L  
5' x 36"  
OVAL  
6' x 36"  
5' x 32" IA-LHO  
5' x 32" IA-RHO  
SAVONA  
MODEL 2908L / LA  
MODEL 2711L  
REMINISCENCE  
ELLISSE  
MODEL 2773L  
CADET 6' x 36"  
CADET 6' x 42"  
CADET CORNER  
5' x 42"  
MODEL 2774L / LA  
MODEL 2775L  
MODEL 2805L  
THANK YOU...  
for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The  
whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the  
whirlpool installation are your selected fittings and electrical connections.  
To insure maximum performance and pleasure from this product, please follow the instructions and cautions.  
FOR AFTER-SALES SERVICE CALL 1 (ꢁ00) ꢂꢂꢀ-1ꢃ0ꢀ WEEKDAYS.  
© AS Americas Inc. ꢀ00ꢁ  
All product names listed herein are trademarks  
of AS Americas Inc. unless otherwise noted.  
753737-100 Rev. C  
1
 
IMPORTANT SAFETY INSTRUCTIONS  
INSTRUCTIONS PERTAINING TO  
A RISK OF FIRE, ELECTRIC SHOCK  
OR INJURY TO PERSONS  
READ AND FOLLOW ALL INSTRUCTIONS!  
!
!
!
WARNING: Risk of personal injury. Do not permit children to use this unit without adult supervision.  
WARNING: Risk of personal injury. Do not operate this unit without the guard over the suction fitting.  
WARNING: Risk of electric shock. Do not permit electrical appliances (hair dryer, telephone, radio, etc.) within  
ꢄ0 inches (15ꢀꢂmm) of this unit.  
!
!
!
!
WARNING: Risk of hyperthermia and possible drowning. People using medications and/or having adverse  
medical history should consult a physician before using this product.  
WARNING: Risk of personal injury. Do not overfill unit before entering. Entering tub when filled more than ꢀ/3  
can cause overflow and slippery conditions. Exercise caution when entering and exiting.  
WARNING: No Food or Alcoholic Beverages. Use of your bathtub immediately after meals is not  
recommended. Avoid alcohol consumption before or during bathing. Alcoholic beverages can cause drowsiness or  
hyperthermia resulting in loss of consciousness or even drowning.  
WARNING: Pregnancy. If you are or think you may be pregnant, consult your physician before using the bathtub.  
Never drop or insert any object into any opening.  
Use this unit only for its intended use as described in this manual. Do not use any attachments not recommended by  
American Standard.  
The unit must be connected only to a supply circuit that is properly protected by a ground-fault circuit-interrupter  
(GFCI). Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI,  
push the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI  
fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the bathtub without the test button  
being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this hydromassage  
bathtub. Disconnect the hydromassage bathtub and have the problem corrected by a licensed electrician before using.  
A pressure wire connector is provided on the exterior of the motor unit to permit connection of a no. ꢁ AWG solid  
copper bonding conductor between this unit and all other electrical equipment and exposed metal in the vicinity, as  
needed to comply with local requirements. To reduce the risk of an electric shock, connect this connector the  
grounding terminal of your electric service or supply panel with a conductor equivalent in size to the circuit conductors  
supplying this unit.  
SAVE THESE INSTRUCTIONS  
753737-100 Rev. C  
3
 
General Installation Information  
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your  
vendor immediately. After inspection and during installation, protect the bath from construction damage. Before  
installation, and before enclosing with wallboard, tile, etc., the bath must be filled with water and operated to  
check for leaks that may have resulted from shipping damage or mishandling! Do not make modifications to  
the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance  
of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.  
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and  
enclosing materials are provided by others.  
For electrical requirements, refer to section titled “Whirlpool Electrical Installation Instructions”.  
Check for availability of optional American Standard wall tiling bead (required for recess installation).  
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.  
!
WARNING: Do not lift whirlpool by the piping harness at any time.  
List of Required Tools and Supplies:  
Tools  
Supplies  
• Level  
• Nails  
• Tape Measure  
• Pipe Wrench  
• Slip Joint Pliers  
• Screw Driver  
• Putty  
• Caulking (waterproof)  
• 1 x ꢂ Stringers  
• Drop Cloth  
• Standard Woodworking Tools  
• Personal Safety Equipment  
• Caulking Gun  
• Cement, Plaster, Grout  
LIST OF OPTIONAL COMPONENTS (NOT INCLUDED):  
Required Components  
(Not Included)  
Optional Components  
(Not Included)  
Description  
Model  
Number  
E-Z  
Install  
Heater  
Tile  
Bead  
Kit  
Drain  
(White)  
Drain  
Bath  
Filler  
Apron  
Kit  
(Specify  
Finish)  
Lifetime™/Evolution™ Corner  
Lifetime™/Evolution™ 5' x 3ꢀ"  
Lifetime™/Evolution™ 5' x 3ꢄ"  
Lifetime™/Evolution™ ꢄ' x 3ꢄ"  
Lifetime™/Evolution™ 5' x 3ꢀ" IA  
Lifetime™/Evolution™ Oval  
Lifetime™ Savona  
ꢄ0ꢄ0  
ꢀꢂꢀꢀ  
ꢀ771  
7ꢀ3ꢄ  
ꢀꢂꢀ5  
ꢀꢄꢂ5  
ꢀꢃ01  
ꢀꢃ0ꢁ  
ꢀ711  
ꢀ773  
ꢀ77ꢂ  
ꢀ775  
ꢀꢁ05  
INCLUDED 0707.ꢀ00  
X
X
X
X
15ꢃꢃ.500.0ꢀ0 15ꢁ3.ꢂ70.XXX  
15ꢃꢃ.500.0ꢀ0* 15ꢃꢃ.ꢀ05.XXX*  
15ꢃꢃ.500.0ꢀ0* 15ꢃꢃ.ꢀ05.XXX*  
15ꢃꢃ.500.0ꢀ0* 15ꢃꢃ.ꢀ05.XXX*  
15ꢃꢃ.500.0ꢀ0* 15ꢃꢃ.ꢀ05.XXX*  
15ꢃꢃ.500.0ꢀ0 15ꢁ3.ꢂ70.XXX  
15ꢃꢃ.500.0ꢀ0 15ꢁ3.ꢂ70.XXX  
15ꢃꢃ.500.0ꢀ0 15ꢁ3.ꢂ70.XXX  
15ꢃꢃ.500.0ꢀ0 15ꢁ3.ꢂ70.XXX  
15ꢃꢃ.500.0ꢀ0 15ꢁ3.ꢂ70.XXX  
15ꢃꢃ.500.0ꢀ0 15ꢁ3.ꢂ70.XXX  
15ꢃꢃ.500.0ꢀ0 15ꢁ3.ꢂ70.XXX  
15ꢁ3.ꢂ70.0ꢀ0 15ꢁ3.ꢂ70.XXX  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
ꢃꢀꢄ1.01ꢃ  
ꢃꢀꢄ1.01ꢃ  
ꢃꢀ71.01ꢃ  
INTEGRAL  
ꢃꢀꢄꢄ.01ꢁ  
X
X
X
NOT  
AVAILABLE  
NOT  
Lifetime™ Reminiscence  
Lifetime™ Ellisse  
AVAILABLE  
NOT  
AVAILABLE  
ꢃꢀ7ꢀ.01ꢁ  
ꢃꢀ7ꢀ.01ꢁ  
Lifetime™ Cadet ꢄ' x 3ꢄ"  
Lifetime™ Cadet ꢄ' x ꢂꢀ"  
Lifetime™ Cadet Corner  
Lifetime™ 5' x ꢂꢀ"  
X
X
X
X
NOT  
AVAILABLE  
ꢃ1ꢄ0.ꢀ00  
• For these components please see your Vendor.  
* These models require American Standard Lifetime™ Drain 15ꢃꢃ.ꢀ05 or 15ꢃꢃ.500  
753737-100 Rev. C  
 
SPECIFICATIONS:  
L
W
J
H
C
A
SIDE VIEW  
END VIEW  
DRAIN / OVERFLOW  
B
GENERAL SPECIFICATIONS FOR LIFETIME / EVOLUTION WHIRLPOOLS AND BATH TUBS  
Description  
Dimensions  
L-W-H  
Drain /  
Height to  
Cut Out  
Pier  
G x F  
Rough-In  
Recess  
E x D  
Tub Edge to  
Centerline  
Overflow: J  
Weight with  
Water / Floor  
Loading  
Product Apron /  
Weight Mounting  
Heater Ready Gallon to Whirlpool  
Overflow Underside  
of Deck: C  
for Field  
Overflow Operating  
Volume  
Installation  
A 1ꢁ"  
L 1ꢃꢂꢃmm (7ꢄ-3/ꢂ")  
W 1ꢄꢄ1mm (ꢄ5-3/ꢁ")  
H 5ꢂꢄmm (ꢀ1-1/ꢀ")  
C 1ꢃ-1/ꢀ"  
(ꢂ57 mm)  
(ꢂꢃ5 mm)  
B 13-3/ꢂ"  
10ꢁ lb.  
(ꢂꢃ kg.)  
Included  
Optional  
Optional  
Optional  
Optional  
Optional  
Optional  
Optional  
Optional  
Optional  
Optional  
Optional  
Optional  
ꢄ0ꢄ0L / V  
Corner*  
Optional  
Optional  
Optional  
Optional  
Included  
Optional  
Optional  
ꢁꢄ gal.  
(3ꢀ5 l.)  
130mm  
(5-5/ꢁ)  
71 gal.  
(ꢀꢄꢃ l.)  
ꢁꢀꢂ lb. (37ꢂ kg)/  
(117 kg/sq.m)  
ꢀ5 lb./sq.ft.  
Template  
provided  
Template  
751ꢄꢁ0-100  
(3ꢂꢃ mm)  
5ꢁ-1/ꢀ"  
A ꢀ0-1/ꢁ"  
C ꢀ0"  
ꢄ0-3/1ꢄ"  
ꢄꢃ0 lb. (313 kg)/  
(ꢀꢄ0 kg/sq.m)  
53 lb./sq.ft.  
L 15ꢀꢂmm (ꢄ0")  
W ꢁ13mm (3ꢀ")  
H 5ꢂꢄmm (ꢀ1-1/ꢀ")  
7ꢂ lb.  
(3ꢂ kg.)  
ꢀꢂꢀꢀL / LA /  
V / VA  
5' x 3ꢀ"  
7ꢂ gal.  
(ꢀꢁ0 l.)  
ꢁ3mm  
(3-1/ꢂ)  
33 gal.  
(1ꢀ5 l.)  
(1ꢂꢁ5 mm)  
x 30-1/ꢀ"  
(77ꢂ mm)  
(511 mm)  
(50ꢁ mm)  
B 11"  
(15ꢀꢁ mm)  
x 30-1/ꢀ"  
(77ꢂ mm)  
(ꢀ7ꢃ mm)  
A ꢀ0-1/ꢁ"  
C ꢀ0"  
5ꢁ-1/ꢀ"  
ꢁ00 lb. (3ꢄ3 kg)/  
(ꢀꢄ0 kg/sq.m)  
53 lb./sq.ft.  
ꢄ0-3/1ꢄ"  
L 15ꢀꢂmm (ꢄ0")  
W ꢃ1ꢂmm (3ꢄ")  
H 5ꢂꢄmm (ꢀ1-1/ꢀ")  
75 lb.  
(3ꢂ kg.)  
ꢀ771L / LA /  
V / VA  
5' x 3ꢄ"  
ꢁ7 gal.  
(3ꢀꢃ l.)  
ꢁ3mm  
(3-1/ꢂ)  
50 gal.  
(1ꢁꢃ l.)  
(511 mm)  
(50ꢁ mm)  
B 11"  
(1ꢂꢁ5 mm)  
x 3ꢂ-1/ꢀ"  
(ꢁ7ꢄ mm)  
(15ꢀꢁ mm)  
x 3ꢂ-1/ꢀ"  
(ꢁ7ꢄ mm)  
(ꢀ7ꢃ mm)  
A ꢀ0-1/ꢁ"  
C ꢀ0"  
70-1/ꢀ"  
1031 lb. (ꢂꢄ7 kg)/  
(ꢀꢁ0 kg/sq.m)  
57 lb./sq.ft.  
7ꢀ-3/1ꢄ"  
L 1ꢁꢀꢃmm (7ꢀ")  
W ꢃ1ꢂmm (3ꢄ")  
H 5ꢂꢄmm (ꢀ1-1/ꢀ")  
10ꢄ lb.  
(ꢂꢁ kg.)  
7ꢀ3ꢄL / LA /  
V / VA  
ꢄ' x 3ꢄ"  
111 gal.  
(ꢂꢀ0 l.)  
ꢁ3mm  
(3-1/ꢂ)  
53 gal.  
(ꢀ01 l.)  
(511 mm)  
(50ꢁ mm)  
B 11"  
(17ꢃ0 mm)  
x 3ꢂ-1/ꢀ"  
(ꢁ7ꢄ mm)  
(1ꢁ33 mm)  
x 3ꢂ-1/ꢀ"  
(ꢁ7ꢄ mm)  
(ꢀ7ꢃ mm)  
A 1ꢃ-1/ꢁ"  
C ꢀ0-1/ꢂ"  
(ꢂꢁ5 mm)  
(515 mm)  
B 10-1/ꢀ"  
ꢄ75 lb. (30ꢄ kg)/  
(ꢀꢄꢀ kg/sq.m)  
5ꢂ lb./sq.ft.  
ꢄ0-3/1ꢄ"  
ꢀꢂꢀ5L / V  
5' x 3ꢀ”  
IA-LHO /  
IA-RHO  
L 15ꢀꢂmm (ꢄ0")  
W ꢁ13mm (3ꢀ")  
H 5ꢀ1mm (ꢀ0-1/ꢀ")  
ꢃꢀ lb.  
(ꢂꢀ kg.)  
70 gal.  
(ꢀꢄ5 l.)  
3ꢃ gal.  
(1ꢂꢁ l.)  
73mm  
(ꢀ-7/ꢁ)  
N/D  
(15ꢀꢁ mm)  
x 30-1/ꢀ"  
(77ꢂ mm)  
(ꢀꢄꢄ mm)  
A 15-1/ꢂ"  
C 1ꢁ-1/ꢂ"  
(3ꢁ7 mm)  
(ꢂꢄꢂ mm)  
B ꢁ-1/ꢂ"  
ꢄꢂ"  
(1ꢄꢀ5 mm)  
x 3ꢂ"  
5ꢁ0 lb. (ꢀꢄ3 kg)/  
(175 kg/sq.m)  
3ꢄ lb./pies  
ꢄꢄ-3/1ꢄ"  
L 1ꢄ7ꢄmm (ꢄꢄ")  
W ꢃ1ꢂmm (3ꢄ")  
H 50ꢀmm (1ꢃ-3/ꢂ")  
ꢃꢄ lb.  
(ꢂꢂ kg.)  
5ꢁ gal.  
(ꢀ1ꢃ l.)  
ꢂꢀ gal.  
(15ꢃ l.)  
ꢂꢂmm  
(1-3/ꢂ)  
ꢀꢄꢂ5L / LA /  
V / VA  
(1ꢄꢁ1 mm)  
x 3ꢂ-1/ꢀ"  
(ꢁ7ꢄ mm)  
Oval  
(ꢀ0ꢃ mm)  
(ꢁꢄ3 mm)  
cuadrados  
A 1ꢄ-1/ꢂ"  
C ꢀ0"  
ꢄꢃ-3/ꢂ"  
(177ꢀ mm)  
x ꢂꢀ"  
ꢃ3ꢄ lb. (ꢂꢀ1 kg)/  
(ꢀ11 kg/sq.m)  
ꢂ3 lb./sq.ft.  
7ꢀ-3/1ꢄ"  
L 1ꢁꢀꢃmm(7ꢀ")  
W 111ꢁmm(ꢂꢂ")  
H 55ꢃmm(ꢀꢀ")  
15ꢀ lb.  
(ꢄꢁ kg.)  
ꢃꢂ gal.  
(35ꢄ l.)  
ꢁꢄ gal.  
(3ꢀꢄ l.)  
1ꢂ0mm  
(5-1/ꢀ)  
ꢀꢃ01L  
Savona  
(ꢂ13 mm)  
(50ꢁ mm)  
B ꢄ-1/ꢀ"  
(1ꢁ33 mm)  
x ꢂꢀ-1/ꢀ"  
(10ꢁ0 mm)  
(1ꢄ5 mm)  
(10ꢄ7 mm)  
A 15-1/ꢁ"  
C 1ꢁ-1/ꢂ"  
(3ꢁꢂ mm)  
(ꢂꢄꢂ mm)  
B ꢄ"  
ꢄ5ꢃ lb. (ꢀꢃꢃ kg)/  
(1ꢃ1 kg/sq.m)  
ꢂ0 lb./sq.ft.  
L 1ꢄ7ꢄmm (ꢄꢄ")  
W ꢃ1ꢂmm (3ꢄ")  
H ꢄ1ꢄmm (ꢀꢂ-1/ꢂ")  
ꢃ5 lb.  
(ꢂ3 kg.)  
ꢄꢁ gal.  
(ꢀ57 l.)  
55 gal.  
(ꢀ0ꢁ l.)  
15ꢀmm  
(ꢄ)  
ꢀꢃ0ꢁL / LA  
Reminiscence  
AS  
DESIRED  
Template  
provided  
(15ꢀ mm)  
7ꢀ-3/1ꢄ"  
(1ꢁ33 mm)  
x ꢂꢁ"  
A 17-3/ꢁ"  
C 1ꢃ-1/ꢀ"  
(ꢂꢂ1 mm)  
(ꢂꢃ5 mm)  
B ꢂ"  
70-1/ꢀ"  
ꢃꢄ5 lb. (ꢂ3ꢂ kg)/  
(1ꢃ5 kg/sq.m)  
ꢂ0 lb./sq.ft.  
L 1ꢁꢀꢃmm (7ꢀ")  
W 1ꢀ1ꢃmm (ꢂꢁ")  
H 5ꢂꢄmm (ꢀ1-1/ꢀ")  
1ꢂꢁ lb.  
(ꢄ7 kg.)  
ꢃ5 gal.  
(3ꢄ0 l.)  
7ꢂ gal.  
(ꢀꢁ0 l.)  
10ꢀmm  
(ꢂ)  
ꢀ711L  
Ellisse  
(17ꢃ1 mm)  
x ꢂꢄ-1/ꢀ"  
(11ꢁ1 mm)  
(1ꢀ1ꢃ mm)  
(10ꢀ mm)  
7ꢀ-3/1ꢄ"  
(1ꢁ33 mm)  
x 3ꢄ"  
A 17"  
70-1/ꢀ"  
751 lb. (3ꢂ1 kg)/  
(1ꢃ0 kg/sq.m)  
ꢂ0 lb./sq.ft.  
L 1ꢁꢀꢃmm (7ꢀ")  
W ꢃ1ꢂmm (3ꢄ")  
H 50ꢀmm (1ꢃ-3/ꢂ")  
C 1ꢁ-1/ꢂ"  
(ꢂ3ꢀ mm)  
(ꢂꢄꢂ mm)  
B 1ꢀ"  
101 lb.  
(ꢂ5 kg.)  
Optional  
Optional  
7ꢁ gal.  
(ꢀꢃꢄ l.)  
ꢄꢂ gal.  
(ꢀꢂ3 l.)  
57mm  
(ꢀ-1/ꢂ)  
ꢀ773L  
Cadet ꢄ' x 3ꢄ"  
(17ꢃ1 mm)  
x 3ꢂ-1/ꢂ"  
(ꢁ70 mm)  
(ꢃ1ꢂ mm)  
(305 mm)  
7ꢀ-3/1ꢄ"  
(1ꢁ33 mm)  
x ꢂꢀ"  
A 1ꢄ-1/ꢂ"  
C 1ꢁ-1/ꢂ"  
(ꢂ13 mm)  
(ꢂꢄꢂ mm)  
B ꢄ-1/ꢀ"  
70-1/ꢀ"  
ꢁꢀ1 lb. (37ꢀ kg)/  
(ꢀ03 kg/sq.m)  
ꢂꢀ lb./sq.ft.  
L 1ꢁꢀꢃmm (7ꢀ")  
W 10ꢄ7mm (ꢂꢀ")  
H 50ꢀmm (1ꢃ-3/ꢂ")  
137 lb.  
(ꢄꢀ kg.)  
ꢁꢀ gal.  
(310 l.)  
ꢄꢄ gal.  
(ꢀ5ꢄ l.)  
57mm  
(ꢀ-1/ꢂ)  
ꢀ77ꢂL / LA  
Cadet ꢄ' x ꢂꢀ"  
(17ꢃ1 mm)  
x ꢄ0-1/ꢀ"  
(1537 mm)  
(10ꢄ7 mm)  
(1ꢄ5 mm)  
A 1ꢄ-1/ꢀ"  
C 1ꢁ-1/ꢂ"  
(ꢂ1ꢃ mm)  
(ꢂꢄꢂ mm)  
B ꢁ-1/ꢀ"  
75ꢄ lb. (3ꢂ3 kg)/  
(115 kg/sq.m)  
3ꢂ lb./sq.ft.  
L ꢀ15ꢃmm (ꢁ5")  
W 15ꢀꢂmm (ꢄ0")  
H 50ꢀmm (1ꢃ-3/ꢂ")  
130 lb.  
(5ꢃ kg.)  
75 gal.  
(ꢀꢁꢂ l.)  
ꢄ0 gal.  
(ꢀ7ꢀ l.)  
ꢀ7ꢃmm  
(11)  
ꢀ775L  
Cadet Corner  
Template  
provided  
(ꢀ15 mm)  
ꢄ0-3/1ꢄ"  
(15ꢀꢁ mm)  
x ꢂꢀ"  
A 1ꢄ-1/ꢂ"  
C 1ꢃ-1/ꢀ"  
(ꢂ13 mm)  
(ꢂꢃ5 mm)  
B ꢄ-1/ꢀ"  
5ꢁ-1/ꢀ"  
ꢄꢁꢃ lb. (310 kg)/  
(1ꢃ1 kg/sq.m)  
3ꢃ lb./sq.ft.  
L 15ꢀꢂmm (ꢄ0")  
W 10ꢄ7mm (ꢂꢀ")  
H 5ꢂꢄmm (ꢀ1-1/ꢀ")  
130 lb.  
(5ꢃ kg.)  
Optional  
ꢄꢂ gal.  
(ꢀꢂ3 l.)  
5ꢀ gal.  
(1ꢃ7 l.)  
15ꢀmm  
(ꢄ)  
ꢀꢁ05L  
5' x ꢂꢀ"  
(1ꢂꢁꢄ mm)  
x ꢂ0-1/ꢀ"  
(10ꢀꢃ mm)  
(10ꢄ7 mm)  
(1ꢄ5 mm)  
TABLE 1  
753737-100 Rev. C  
5
 
ROUGHING-IN REFERENCES  
6' x 36" (MODEL 7236L / LA / V / VA)  
5' x 32" (MODEL 2422L / LA / V / VA)  
7ꢀ"  
(1ꢁꢀꢃmm)  
ꢄ0"  
(15ꢀꢂmm)  
11"  
(ꢀ7ꢃmm)  
3-1/ꢂ"  
(ꢁ3mm)  
13-3/ꢂ"  
13-3/ꢂ"  
(3ꢂꢃmm)  
3"  
(3ꢂꢃmm)  
7-3/ꢂ"  
(1ꢃ7mm)  
(7ꢄmm)  
3"  
(7ꢄmm)  
3ꢄ"  
(ꢃ1ꢂmm)  
3ꢀ"  
(ꢁ13mm)  
ꢄ"  
(15ꢀmm)  
ꢄ"  
(15ꢀmm)  
CUT OUT IN FLOOR  
FOR DRAIN  
7-3/ꢂ"  
(1ꢃ7mm)  
CUT OUT IN FLOOR  
FOR DRAIN  
3-1/ꢂ"  
(ꢁ3mm)  
11"  
(ꢀ7ꢃmm)  
5' x 36" (MODEL 2771L / LA / V / VA)  
OVAL (MODEL 2645L / LA / V / VA)  
ꢄ0"  
(15ꢀꢂmm)  
ꢄꢄ"  
(1ꢄ7ꢄmm)  
11-1/ꢂ"  
11"  
(ꢀ7ꢃmm)  
(ꢀꢁꢄmm)  
1-3/ꢂ"  
(ꢂꢂmm)  
3-1/ꢂ"  
(ꢁ3mm)  
1ꢁ"  
(ꢂ57mm)  
ꢄ"  
CUT OUT IN FLOOR  
(15ꢀmm)  
3ꢄ"  
(ꢃ1ꢂmm)  
FOR DRAIN  
3"  
(7ꢄmm)  
ꢄ"  
CUT OUT IN FLOOR  
FOR DRAIN  
3ꢄ"  
(15ꢀmm)  
(ꢃ1ꢂmm)  
7-1/ꢀ"  
(1ꢃ1mm)  
13-3/ꢂ"  
(3ꢂꢃmm)  
3"  
(7ꢄmm)  
5-3/ꢁ"  
ꢁ-1/ꢂ"  
(ꢀ10mm)  
(137mm)  
5' x 32" IA-LHO (MODEL 2425L/V-LHO) - shown  
5' x 32" IA-RHO (MODEL 2425L/V-RHO)  
ꢄ0"  
(15ꢀꢂmm)  
10-1/ꢀ"  
(ꢀꢄ7mm)  
7-1/ꢀ"  
(1ꢃ1mm)  
3"  
(7ꢄmm)  
ꢀ-7/ꢁ"  
(73mm)  
1ꢄ"  
(ꢂ0ꢄmm)  
ꢄ"  
(15ꢀmm)  
3ꢀ"  
(ꢁ13mm)  
CUT OUT IN FLOOR  
FOR DRAIN  
13-1/ꢀ"  
(3ꢂ3mm)  
DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE  
OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z1ꢀꢂ.1 AND A11ꢀ.1ꢃ.7.  
753737-100 Rev. C  
 
ROUGHING-IN REFERENCES  
CORNER (MODEL 6060L / V)  
SAVONA (MODEL 2901L)  
76-3/4"  
(1949mm)  
72"  
(1829mm)  
54-1/2"  
(1384mm)  
65-3/8"  
(1661mm)  
44"  
(1118mm)  
11-1/2"  
(292mm)  
3
"
6"  
8"  
(76mm)  
3"  
(76mm)  
(152mm)  
(203mm)  
10"  
(254mm)  
15"  
12  
"
17-3/4"  
(451mm)  
(381mm)  
(305mm)  
5-1/2"  
(140mm)  
7"  
(178mm)  
5-5/8"  
(143mm)  
7" (178mm)  
CUT OUT  
IN FLOOR FOR DRAIN  
13-3/4" (349mm)  
RECOMMENDED FITTING LOCATION  
64 X 279mm (2-1/2 X 11)  
CADET CORNER (MODEL 2775L)  
229 X 305mm  
(9 X 12  
CUTOUT IN  
FLOOR FOR  
DRAIN  
1080mm  
"
")  
(42-1/2  
")  
1076mm  
(42-3/8  
")  
1524mm  
(60  
165mm  
(6-1/2)  
"
)
70mm REF.  
(2-3/4)  
PROVIDE ACCESS TO  
PUMP FOR  
SERVICING ON ALL  
INSTALLATIONS  
RECOMMENDED  
FITTING  
LOCATION  
64 X 330mm  
PUMP  
(2-1/2 X 13  
")  
OUTLINE OF  
CUTOUT  
279mm  
(11  
")  
C/L  
1080 mm  
C/L OF DRAIN OUTLET  
(42-1/2  
")  
2159mm  
(85  
"
)
5X42 (MODEL 2805L)  
ELLISSE (MODEL 2711L)  
1524mm  
1829mm  
(60  
")  
(72  
")  
(36-1/2  
927mm  
")  
INTEGRAL  
FITTING DECK  
102mm  
(4  
152mm  
(6  
OUTLINE OF CUTOUT  
1791 X 1181  
762mm  
(30  
"
)
"
)
"
)
(70-1/2 X 46-1/2")  
"
305mm  
305mm  
C/L OF  
DRAIN  
(12  
")  
(12  
")  
C/L OF  
DRAIN  
PUMP  
178mm x 381mm  
(7  
FLOOR  
CUTOUT  
"
x 15")  
229mm x 356mm  
(9 x 14 ) FLOOR  
CUTOUT  
"
"
1219mm  
(48  
PUMP  
"
)
1067mm  
(42  
"
)
19mm  
(3/4  
"
)
OUTLINE OF CUTOUT  
1486mm x 1029mm  
PROVIDE ACCESS  
TO PUMP FOR  
SERVICE ON ALL  
INSTALLATIONS  
(58-1/2 x 40-1/2")  
"
PROVIDE ACCESS TO  
PUMP FOR SERVICE  
ON ALL INSTALLATIONS  
OPTIONAL DECK  
FITTING AREA  
RECOMMENDED  
GRAB BAR  
FITTING AREA  
FITTING LOCATION  
64 X 279mm (2-1/2" X 11")  
DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE  
OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z124.1 AND A112.19.7.  
753737-100 Rev. C  
7
 
ROUGHING-IN REFERENCES  
REMINISCENCE (MODEL 2908L / LA)  
CADET 6 x 42 (MODEL 2774L / LA)  
1ꢄ7ꢄmm  
(ꢄꢄ")  
330mm  
(13  
PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS  
1ꢁꢀꢃ mm  
"
)
(7ꢀ)  
PUMP  
305 mm  
RECOMMENDED FITTING LOCATION  
ꢄꢂ X 330mm (ꢀ-1/ꢀ x 13")  
FOR PIER OR ISLAND  
(1ꢀ)  
ꢀꢀꢃmm  
(ꢃ)  
ꢃ1ꢂmm  
(3ꢄ")  
1ꢃ mm  
(3/ꢂ)  
ꢀꢀꢃ x 305mm  
(ꢃ X 1ꢀ)  
INSTALLATIONS ONLY  
ꢂ57mm  
(1ꢁ)  
FINISHED  
WALL  
FLOOR  
CUTOUT  
ꢄꢂmm REF.  
(ꢀ-1/ꢀ)  
INTEGRAL  
FITTING  
DECK  
ꢀꢀꢃ mm  
(ꢃ)  
10ꢄ7mm  
(ꢂꢀ)  
PUMP  
CUTOUT IN FLOOR  
FOR DRAIN  
533mm  
(ꢀ1)  
PROVIDE ACCESS TO  
15ꢀmm  
OUTLINE OF  
CUTOUT  
PUMP FOR SERVICE  
(ꢄ)  
C/L OF DRAIN  
OUTLET  
ON ALL INSTALLATIONS  
OUTLINE OF  
CUTOUT  
17ꢃ1mm x 10ꢀꢃmm  
(70-1/ꢀ X ꢂ0-1/ꢀ)  
(ꢀ) AIR VALVES  
57mm  
(ꢀ-1/ꢂ)  
(ꢁ) JETS  
ALT. FITTING  
LOCATION #1  
C/L OF DRAIN  
CADET 6 x 36 (MODEL 2773L)  
PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS  
1ꢁꢀꢃ mm  
(7ꢀ)  
ꢀꢀꢃmm  
(ꢃ)  
305 mm  
(1ꢀ)  
RECOMMENDED FITTING LOCATION  
ꢄꢂ X 330mm (ꢀ-1/ꢀ x 13")  
FOR PIER OR ISLAND  
1ꢃ mm  
(3/ꢂ)  
INSTALLATIONS ONLY  
FINISHED  
WALL  
ꢃ0ꢁ mm  
(35-3/ꢂ)  
ꢀꢀꢃ mm  
(ꢃ)  
PUMP  
CUTOUT IN FLOOR  
FOR DRAIN  
ꢂ5ꢂ mm  
(17-7/ꢁ)  
OUTLINE OF CUTOUT  
17ꢃ1 mm x ꢁ70 mm  
(70-1/ꢀ X 3ꢂ-1/ꢂ)  
(ꢀ) AIR VALVES  
57mm  
(ꢀ-1/ꢂ)  
(ꢁ) JETS  
ALT. FITTING  
LOCATION #1  
C/L OF DRAIN  
DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE  
OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z1ꢀꢂ.1 AND A11ꢀ.1ꢃ.7.  
753737-100 Rev. C  
 
INSTALLATION AND FRAMING INSTRUCTIONS  
The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs as needed. Ensure  
roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an access opening for servicing the pump  
and controls. It is strongly recommended that an additional opening be provided for access to the drain components. The apron should not be used  
as the primary access opening.  
1. Position the whirlpool into the installation opening and level the deck in both directions, shimming the integral support feet IF necessary.  
Mark the final position of the underside of the deck by tracing a line on to the studs (see Figure 1).  
ꢀ. Remove the whirlpool and attach a 1 x ꢂ stringer to the studs, with the top of the stringer touching the traced line.  
!
The rim of the bath must not support weight.  
FIGURE 1  
TYPICAL INSTALLATION  
3. Install drain components to the whirlpool following the drain installation instructions. Before  
replacing your whirlpool for final installation, be certain that an opening has been provided in  
the sub-floor for the drain. See the roughing-in drawing and Table 1 for suggested opening  
size (shadowed) and location dimensions. The drain/overflow of the bath extends below the  
bottom of the bath. Note that this requires a cutout in the floor.  
The floor structure beneath the bath must be able to support a total weight of bath, water, and  
bather. Refer to Table 1 under total weight for your model.  
!
For Models: 2425L/V-LHO and 2425L/V-RHO;  
This bath must be supported along its entire bottom. Use mortar as bedding  
material (do not use sand or foam). Apply enough mortar to support the complete  
bottom of the bath. After the mortar has been poured, and before it sets, position  
whirlpool or bath within recess until the rim is leveled against the leveling stringers (see  
"Typical Recess Installation") shown below.  
C
The rim of the bath must not support weight. Allow the mortar material to completely  
harden before applying weight to the rim or bottom of the bath. Any finish material such  
!
TILE  
as tile or wall board must be self-supporting if it contacts the deck of the bath.  
WALLBOARD  
SEALANT  
BATH  
TILE  
BEAD  
STRIP  
For Models: 2645L/V, 2771L/V, 6060L/V, 7236L/V, 2422L/V and 2422LA/VA;  
Replace whirlpool and re-shim the integral support feet, shimming the entire length of  
the support feet. Secure the shims using construction adhesive, silicone, mortar or  
equivalent materials. While not a necessity, the use of a foundation base consisting of  
cement, mortar, or grout will help provide a solid and secure installation.  
ADHESIVE  
LEVELING STRINGER  
1 x ꢂ (not for support)  
The rim of the bath must not support weight. If foundation base is used, allow the  
!
bedding material to completely harden before applying weight to the rim or bottom of  
the bath. Any finish material such as tile or wall board must be self-supporting if it  
contacts the deck of the bath.  
NOTE: Tile bead kit not included and  
must be purchased separately.  
TYPICAL PIER TYPE INSTALLATION  
TYPICAL RECESS INSTALLATION  
AS DESIRED  
F
CUTOUT  
G
CUTOUT  
C
C
1ꢀ  
(305 mm)  
1ꢀ  
(305 mm)  
AS DESIRED  
E
MOUNTING  
SURFACE  
LEVELING  
STRINGERS  
NOTE:  
ꢀꢂ  
(ꢄ10 mm)  
FRONT EDGE  
WATERPROOF  
SEALANT  
ꢀꢂ  
(ꢄ10 mm)  
OF BATH MUST  
BE SUPPORTED  
BY STUD WALL OR  
AMERICAN STANDARD  
APRON KIT  
ACCESS PANEL MUST BE LOCATED  
ON THE SAME SIDE AS THE MOTOR.  
ACCESS PANEL MUST BE LOCATED  
ON THE SAME SIDE AS THE MOTOR.  
BATH  
ALLOW OPEN FRAMING ON  
PUMP/MOTOR END FOR SERVICE.  
ACCESS PANELS NOT REQUIRED  
FOR BATH TUBS.  
ALLOW OPEN FRAMING ON PUMP/MOTOR  
END FOR SERVICE.  
ACCESS PANELS NOT REQUIRED  
FOR BATH TUBS.  
UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)  
IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.  
(EXCEPT 2425 WHERE APRON IS PRIMARY ACCESS OPENING)  
UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)  
IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.  
FOR E & D DIMENSIONS SEE TABLE 1 ON PAGE 5.  
FOR G & F DIMENSIONS SEE TABLE 1 ON PAGE 5.  
753737-100 Rev. C  
 
TYPICAL FLANGE MOUNTING DETAIL  
SUGGESTED WHIRLPOOL / BATH  
INSTALLATION METHOD  
TYPICAL INSTALLATION -  
CORNER  
WOOD  
STUDS  
STUD  
WATERPROOF DRYWALL  
OR CEMENT BOARD  
TILE  
ROOFING NAIL  
SEALANT  
TUB  
1ꢃ-1/ꢀ  
(ꢂꢃ5mm)  
1 x 3 (ꢀ5 x 7ꢄmm) WOOD  
STRINGER FULL LENGTH  
STEEL  
STUDS  
STEEL  
STUD  
WHIRLPOOL  
ACCESS PANEL  
WASHER  
WATERPROOF DRYWALL  
OR CEMENT BOARD  
TILE  
SEALANT  
* SEE CUTOUT TEMPLATE  
PROVIDED ON UNDERSIDE  
OF BOX LID  
ꢂ" (10ꢀmm)  
DRYWALL  
SCREW  
TUB  
1 x 3 (ꢀ5 x 7ꢄmm) WOOD  
STRINGER FULL LENGTH  
UNLESS AN ACCESS OPENING OF AT LEAST  
12" x 24" (305 x 610mm) IS PROVIDED,  
WARRANTY SERVICE WILL NOT BE PERFORMED.  
SECURE THE BATH TO THE STUDS AS SHOWN  
FOR WOOD OR STEEL STUD CONSTRUCTION.  
UNDER DECK MOUNTING INSTRUCTIONS  
Please note that care must be taken to protect the surface of the tub during all aspects of the installation.  
Do not drill or cut the bath deck with the tub directly beneath it as damage to the tub may result.  
1. Install the tub per the installation instructions provided with the unit.  
ꢀ. Prepare the bath deck support structure per the local codes. Note - the bath deck must be self supporting.  
3. Cut bath deck to your specifications.  
ꢂ. Place the bath deck in position and trace the opening on the tub with a soft pencil. Do not drill or cut the bath  
deck with the tub directly beneath it as damage to the tub may result.  
5. Remove the bath deck and apply a generous bead of waterproof sealant on the outer edge of the traced line.  
ꢄ. Replace the bath deck and secure it into place.  
7. Apply additional sealant along the tub and bath deck interface as necessary to ensure a watertight seal.  
ꢁ. Remove excess sealant per the manufacturer's instructions.  
Finished bath deck surface material must be  
self-supporting and secured per local codes  
Waterproof  
Bath deck support material  
Sealant  
Bathtub  
Tub support structure per installation  
instructions provided with the tub  
753737-100 Rev. C  
10  
 
WHIRLPOOL ELECTRICAL INSTALLATION INSTRUCTIONS  
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes.  
WARNING: When using electrical products, basic precautions should always be observed, including the following:  
1. DANGER: RISK OF ELECTRIC SHOCK! Connect only to a circuit protected by a ground-fault circuit interrupter.  
ꢀ. Grounding is required. The unit should be installed by a licensed electrician and grounded.  
3. Permit access for servicing motor as noted.  
!
ꢂ. All building materials and wiring should be routed away from the pump body and heater (if equipped).  
PLEASE SEE THE FOLLOWING TABLE FOR GFCI CIRCUIT REQUIREMENTS:  
GFCI CIRCUIT REQUIREMENTS:  
FOR MODEL NUMBERS:  
2422, 2425, 2645,  
2771, 2805, 2908  
ALL MODELS  
The whirlpool should be installed on a 120 vac, 15 amp dedicated  
GFCI circuit.  
The circuit should be hard-wired from the electrical power supply panel. The  
circuit must be a three (3) wire circuit from the electrical supply panel. A  
grounded neutral wire and a third wire, earth ground, are essential.  
7236, 2774  
MODELS ENDING IN SUFFIX  
LA, LAC, VA, VAC  
Optional heater requires a separate 15 amp maximum GFCI circuit.  
The whirlpool should be installed on a 120 vac, 20 amp dedicated  
GFCI circuit.  
6060, 2775, 2773, 2711, 2901  
ALL MODELS  
The circuit should be hard-wired from the electrical power supply panel. The  
circuit must be a three (3) wire circuit from the electrical supply panel. A  
grounded neutral wire and a third wire, earth ground, are essential.  
7236, 2774  
MODELS ENDING IN SUFFIX  
L, LC, V, VC  
Optional heater requires a separate 15 amp maximum GFCI circuit.  
120 VAC  
PUMP/MOTOR  
GND.  
ELECTRICAL DIAGRAM  
READ AND FOLLOW ALL INSTRUCTIONS  
WIRE SELECTION GUIDE  
Maximum distance from  
fusebox to motor  
The sizes shown on this  
chart are recommendations  
for copper conductors  
only. Always follow  
local and national  
Motor  
Hi Performance  
Rating  
50'  
12  
100'  
150'  
200'  
115V Power Line  
10  
2.1 H.P.,  
electrical codes  
1.4 H.P.,  
and 1.25 H.P.  
8
8
753737-100 Rev. C  
11  
 
For 6060L/V Corner Only  
OPERATION  
Fig. 1  
WARNING: Prior to operation, review the Important Safety Instructions  
listed at the beginning of this instruction manual.  
Once the heater is installed and the whirlpool pump is operating, the heater is  
totally automatic. The heater will help maintain the temperature of the water in  
the bath.  
WHIRLPOOL  
HEATER  
L™  
E-Z INSTAL  
HEATER “ON” LIGHT  
Pressure Switch  
FACTORY INSTALLED - NOT FOR RESALE  
HEATER P/N: 753174-100  
The heater is equipped with a preset pressure switch. The pump must be  
running with water flowing in the whirlpool to allow the heater to turn on.  
Bonding Lug on  
Heater Housing  
Indicator Light  
This light turns on whenever the heater is operating.  
High-Limit Switch  
The heater includes an exclusive "Intelligent High-Limit". This safety circuit will not "false trip" from hot tap water. It will only turn the heater  
off if the thermostat fails. If the high-limit trips frequently, call a service technician.  
To manually reset the circuit in the event that the “High-Limit” switch has been activated, simply (1) Turn off the whirlpool pump. (ꢀ) Drain  
water from the tub. (3) Remove power from heater by unplugging at receptacle or turning off circuit breaker. (ꢂ) The heater circuit will  
automatically reset in less than 15 minutes. (5) Restore power to the heater. (ꢄ) Whirlpool bath is now ready to use.  
ELECTRICAL CONNECTIONS  
Install a separate 1ꢀ0VAC / 15AMP dedicated circuit with GFCI (Ground Fault Circuit Interrupter) protection.  
At initial start-up with power ON, push the GFCI test button. The reset button should pop out. Push this button in to reset. If the GFCI fails to  
operate in this manner, there is a ground fault or malfunction, indicating the possibility of electrical shock. Turn off the power and do not  
use the bath until the source of the problem has been identified and corrected.  
1. Route two separate branch circuits to the junction box near the whirlpool as shown in Figure ꢀ. Each branch circuit MUST BE GFCI  
PROTECTED and must use copper conductors only.  
ꢀ. Ensure the heater and pump are properly GROUNDED and BONDED as required. Attach the ꢁ AWG solid copper conductor supplied with  
the heater from the heater bonding lug to the motor frame bonding lug as shown in Figure 3. The conductor is secured to the lugs using set  
screws. The motor frame shall have a second ꢁ AWG solid copper conductor connected from the frame bonding lug to the homes electrical  
panel or approved local bonding point as shown in Figure 3.  
SEPARATE  
15 AMP GFCI OUTLET  
Fig. 2  
Fig. 3  
ELECTRICAL INSTALLATION  
120 VAC  
(HEATER)  
(PUMP/MOTOR)  
GND.  
HEATER  
RUN ꢁ AWG SOLID COPPER  
CONDUCTORS FROM  
HEATER BONDING LUG TO  
PUMP/MOTOR FRAME LUG  
AND FROM PUMP/MOTOR  
LUG TO APPROVED  
SEPARATE 15 AMP GFCI OUTLET  
for 1.6 H.P. PUMP  
SEPARATE 20 AMP GFCI OUTLET  
for2.1 H.P. PUMP  
GROUND AS SHOWN  
120 VAC  
FIRST COPPER  
CONDUCTOR  
SECOND  
COPPER  
CONDUCTOR  
PUMP/MOTOR FRAME WITH  
BONDING LUGS  
TO GROUND  
PUMP/MOTOR  
GND.  
ELECTRICAL DIAGRAM  
READ AND FOLLOW ALL INSTRUCTIONS  
753737-100 Rev. C  
1ꢀ  
 
DRAIN CONNECTION AND SYSTEM TEST  
Using recommended drain assembly, connect whirlpool drain to waste line in accordance with the drain assembly instructions.  
Tighten all drain joints securely. Check the pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with  
water to a point ꢀ" above the top of the highest jet. Recheck the pump couplings and make certain that they are not leaking.  
(Although the pump couplings are factory tightened and inspected, some loosening may have occurred during transit.) Make sure  
the whirlpool is connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the  
whirlpool is running.  
POST INSTALLATION CLEAN-UP  
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use  
wire brushes or any other metal implement on bath surface.  
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains  
®
may be removed using granular Spic and Span mixed with water.  
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.  
AFTERCARE and CLEANING  
• The high gloss surface is resistant to impact and chemicals and will retain its lasting luster with proper care and  
maintenance.  
• Always fill the tub with temperate water. Excessively hot water may cause surface damage  
• Remove bath mat after use and hang to dry. Allowing bath mat to dry in the tub may cause surface damage.  
• Clean after use with a mild liquid household detergent cleaner. Do not use Lestoil, Lysol Disinfectant (spray or  
concentrate), or Lysol Basin, Tub and Tile Cleaner, Windex, Mr. Clean, Dow Disinfectant Bathroom Cleaner, or  
cleaning products in aerosol cans.  
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.  
• Do not use wire brushes, knives or sharp objects to remove stains, cigarette tar deposits,or other surface blemishes.  
• Abrasive cleaners or powders must not be used, since they will dull the surface. If the glossy surface looses  
its sheen, dulled areas can be restored by rubbing with a white "automotive type" polishing compound and  
waxing with a "liquid wax."  
Do not wax areas where you walk or stand.  
• Do not allow nail polish remover, acetone, dry cleaning fluid, paint remover or other solvents to come into  
contact with the surface.  
• Clean the surrounding surface immediately after using caustic drain cleaners.  
• Burning cigarettes will damage the surface.  
• Should damage to the fixture occur, repairs can be made quickly and easily.  
Your distributor or builder can provide details.  
• Do not permit drain cleaner to enter the circulation system.  
CIRCULATION SYSTEM CLEANING-PURGING PROCEDURES  
STEP 1. Once every month purge and clean the circulating system. Fill whirlpool with warm water and add two teaspoons  
of dishwasher detergent and one-half cup of house hold bleach.  
STEP 2. Activate whirlpool system in accordance with operating instructions or two minutes.  
STEP 3. Drain and refill whirlpool with cool water and circulate for additional five minutes.  
STEP 4. Drain whirlpool completely.  
753737-100 Rev. C  
13  
 
AS AMERICA, INC. (AMERICAN STANDARD) LIMITED LIFETIME WARRANTY  
FOR LIFETIME™ / EVOLUTION™ ACRYLIC WHIRLPOOLS  
AS America (“American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this whirlpool or any  
of its parts that are found by American Standard, in its sole judgment, to be defective under normal residential use and maintenance so long  
as it is owned by the original consumer purchaser.  
This warranty shall only become effective upon receipt by American Standard of a completely filled out Warranty Registration Card evidencing  
proof of purchase.  
THIS WARRANTY SHALL BE VOID IF THE ACCESS PANEL TO THE WHIRLPOOL IS COVERED IN ANY MANNER CONTRARY TO THE  
INSTALLATION INSTRUCTIONS. In no event will American Standard be liable for the cost of repair or replacement of any installation  
materials including but not limited to tiles, marble etc.  
This limited warranty DOES NOT COVER the following:  
1. Defects or damages arising from shipping, installation, alterations, accidents, abuse, misuse, lack of proper maintenance and cleaning as  
directed in the owner’s manual and use of other than genuine American Standard replacement parts, in all cases whether caused by a  
plumbing contractor, service company, the owner or any other person.  
ꢀ. Deterioration through normal wear and tear and the expense of normal maintenance.  
3. Commercial application.  
ꢂ. Options and accessories. American Standard’s limited warranty on these items is one year for parts only and excludes labor. This one  
year limited warranty covers accessories manufactured by American Standard (e.g. aprons, drains, grab bars, heaters, trim kits) against  
defects of material or workmanship. Warranty coverage begins on the date the accessory was originally purchased by the owner.  
5. Postage or shipping costs for returning products for repairs or replacement under this limited warranty and labor or other costs incurred in  
connection with product removal or installation under this limited warranty.  
ꢄ. ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, ALL OF WHICH ARE HEREBY EXPRESSLY DISCLAIMED, OR  
THE EXTENSION BEYOND THE DURATION OF THIS LIMITED WARRANTY OF ANY IMPLIED WARRANTIES, INCLUDING THOSE OF  
MERCHANTABILITY OR FITNESS FOR AN INTENDED PURPOSE. (Some jurisdictions do not allow limitations on how long an implied  
warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you.)  
7. Responsibility for compliance with local code requirements. (Since local code requirements vary greatly distributors, retailers, dealers,  
installation contractors and users of plumbing products should determine whether there are any code restrictions on the installation or use of a  
specific product.)  
This warranty gives you specific legal rights. You may have other legal rights that vary from state to state. For service under this warranty, you  
should contact the following:  
By Telephone:  
1-800-442-1902  
By Mail: American Standard Inc.  
P.O. Box ꢄ5ꢃ  
West Caldwell, N.J. 07007  
Attention: Customer Care Center  
AS AMERICA, INC. (AMERICAN STANDARD) ONE YEAR LIMITED WARRANTY  
FOR E-Z INSTALL WHIRLPOOL HEATER  
If inspection of this AS American, Inc. (“American Standard”) plumbing product, within one year after its initial purchase, confirms that it is  
defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.  
This warranty applies only to the original purchaser and installation of these products.  
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this  
product should check with a local building or plumbing contractor to insure local code compliance before installation.  
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance,  
abuse, misuse, accident or other damages; if it was not installed in accordance with American Standard's instructions; or if it has been  
modified in a manner inconsistent with the product as shipped by American Standard.  
American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or  
installation, nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product  
defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or  
provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)  
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in  
which case this warranty does not affect such statutory rights.  
For service under these warranties, it is suggested that a claim be made through the contractor or dealer from or through whom the product  
was purchased, or that a service request (including a description of the product model and of the defect) be sent to:  
By Telephone:  
1-800-442-1902  
By Mail: American Standard Inc.  
P.O. Box ꢄ5ꢃ  
West Caldwell, N.J. 07007  
Attention: Customer Care Center  
SERVICE: For service or repair contact the number below. The model number and  
serial number for your whirlpool are located on a label near the motor.  
HOTLINE FOR HELP  
For toll-free information and answers to your questions, call 1 (800) 442-1902  
weekdays: ꢁ:00 a.m. to 5:00 p.m. Eastern Time  
Product names listed herein are trademarks of AS America, Inc.  
© AS America, Inc. ꢀ00ꢁ  
753737-100 Rev. C  
1ꢂ  
 

3Com Network Router 3CRWDR200A 75 User Manual
Accusplit Heart Rate Monitor AX740SBL User Manual
Acer Computer Monitor UMVH6AA003 User Manual
Alliance Laundry Systems Clothes Dryer 504523R3 User Manual
American Audio CD Player CDS 1 User Manual
American Standard Outdoor Shower 1660502002 User Manual
AMX Network Card TX MLCD User Manual
Bakers Pride Oven Oven Y 600 DSP User Manual
BB Electronics Stereo System CR 25E User Manual
Behringer Microphone C 3 User Manual