American Standard Plumbing Product 621001 User Manual

INSTALLATION INSTRUCTIONS  
CARE AND MAINTENANCE  
ABOVE COUNTER SINK FOR USE WITH: 0621.001 STUDIO  
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read  
these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.  
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!  
NOTE: Pictures may not exactly define contour of china and components.  
!
RECOMMENDED FAUCET : 2064.101 ONE lavatory faucet  
*
*
RECOMMENDED TOOLS AND MATERIALS  
Putty Knife  
Hacksaw  
Regular Screwdriver  
Phillips Screwdriver  
Tape Measure  
Adjustable Wrench  
Pipe Wrench  
Channel Lock Pliers  
Basin Wrench  
Jig Saw  
Drill  
Tubing Cutter  
Silicone Adhesive  
Plumber’s Putty or Caulking  
OBSERVE LOCAL PLUMBING AND BUILDING CODES  
COUNTERTOP INSTALLATION  
Using the template provided, locate the position of the sink  
on the countertop. Provide proper clearance under the  
countertop for the faucet supply lines, drain assembly and  
the structural parts of the cabinet.  
NOTE: If replacing an existing sink be certain to shut off  
water supply before removing old sink.  
1
2
5
After checking fit  
and alignment,  
turn sink upside  
down and apply a  
generous portion  
of silicone  
adhesive around  
the under side of  
the rim near the  
edge. Place sink in  
position. Wipe off  
excess adhesive.  
Drill a clearance hole inside the perimeter line of the  
template for countertop installation.  
Perimeter of  
Perimeter  
template  
of  
template  
6
Cut opening around the perimeter of the template.  
Mounting holes are provided on the rear of the  
lavatory so it can be secured to the wall if desired.  
3
Mount the faucet and drain  
assembly (not included) on  
the sink following the  
7
manufacturer’s instructions.  
Be certain to apply a bead  
Connect supply line to  
faucet (finger tight) and  
carefully bend tubes to  
engage with the supply  
shut-off valves. Tighten  
connections at faucet  
and shut-off valves for  
secure seal.  
A
of sealing putty on the  
underside of the drain (Part  
“A”) in order to ensure a  
watertight seal between the  
sink and drain. Remove  
excess putty after installing  
drain on sink.  
Shut-Off Valves  
4
8
Connect trap to drain  
assembly hand tight to  
check alignment. It may  
be necessary to cut off  
part of the tailpiece (area  
“B”) or part of the  
horizontal leg of the trap  
(area “C”). Secure joints  
for watertight assembly.  
C
B
• Place the sink temporarily into the template.  
• Check for alignment and clearance.  
• Mark the sink and countertop in several places  
as a guide for the installation location.  
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .  
A S A m e r i c a , I n c . 2 0 0 9  
7301244-100 Rev. A  
©
 

2nd Ave Gas Grill DVD V7200 User Manual
ADIC Switch Switches User Manual
Agri Fab Lawn Aerator 45 0406 User Manual
Aiphone Speaker System LAF 10S User Manual
Alamo Lawn Mower 4837 User Manual
Alpine Car Stereo System iDA X100M User Manual
American DJ DJ Equipment 700TM User Manual
American Standard Hot Tub ANSI Z1241 User Manual
Apple MP3 Player Nike + iPod User Manual
Atmel Computer Hardware AT88SC0104CRF User Manual