American Standard Plumbing Product M968628 REV13 User Manual

Installation  
Instructions  
STUDIO  
T590.50X  
PRESSURE BALANCING  
BATH AND SHOWER  
TRIM KITS  
Thank you for selecting American-Standard...the benchmark  
of fine quality for over 100 years.  
To ensure that your installation proceeds smoothly--please  
read these instructions carefully before you begin.  
Certified to comply with ANSI A112.18.1  
M968628 REV.1.3  
Recommended Tools  
Phillips Screwdriver  
Adjustable Wrench  
Channel Locks  
Plumbers' Putty or Caulking  
Teflon Tape  
Flat Blade Screwdriver  
ROUGHING-IN DIMENSIONS (For reference only)  
To assure proper positioning in relation to wall, note roughing-in dimensions.  
INLETS  
1/2" NOM.  
COPPER  
SWEAT  
INLETS  
4-1/16"  
1-5/8" TO 3-1/4"  
FINISHED WALL  
SHR. 1/2" NOM.  
COPPER SWEAT  
2-3/8"  
2-3/8"  
SWEAT  
INLETS  
1/2" NPT  
2"  
4-1/16"  
4-1/16"  
4-1/2"REF.  
4-7/8" REF.  
OPTIONAL TO  
FINISHED FLOOR  
USUALLY  
TUB 1/2" NOM.  
COPPER SWEAT  
BETWEEN  
8-1/2" REF.  
80'' AND 86'  
7-1/2" REF.  
SWEAT  
INLETS (STOPS)  
5-7/8"  
SHR. 1/2" NOM.  
COPPER SWEAT  
TUB 1/2" NOM.  
COPPER SWEAT  
74" FOR  
HEAD  
CLEARANCE  
INLETS  
1/2" NOM.  
COPPER  
"SEE ILLUSTRATION"  
8-1/4"  
SWEAT  
SHR  
TUB  
INLETS 1/2" NPT  
6-11/16"  
3-3/8"  
18"  
OPTIONAL  
3-3/8"  
4-3/4"  
OUTLETS  
1/2" NPT  
OUTLETS  
1/2" NPT  
5-7/8"  
INLETS  
1/2" NPT  
1/2" COPPER  
1" MIN.  
4"  
TOP OF  
TUB RIM  
THREADED INLETS  
3-3/8"  
BOTTOM OF  
TUB  
THREADED INLETS (STOPS)  
 
ADJUST HOT LIMIT STOP  
3
HOT LIMIT SAFETY STOP ADJUSTMENT  
By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP  
reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust  
the setting on the HOT LIMIT SAFETY STOP.  
Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP (1). Follow Step "A" or "B"  
to adjust min./max. discharge temperature. "0" being the hottest to "7" the coldest temperature setting. Factory set at "0".  
"RED RING"- HOT  
LIMIT SAFETY STOP  
1
"A"  
"A"  
ADJUSTMENT WHEN  
WATER IS TOO HOT  
"B"  
PRY RED RING  
"B"  
FORWARD AND ROTATE  
ADJUSTMENT WHEN  
WATER IS TOO COLD  
COUNTER-CLOCKWISE  
ONE CLICK  
TEMPERATURE  
SETTING  
NUMBERS  
PRY RED RING  
FORWARD AND  
ROTATE CLOCKWISE  
SERVICE  
4
If faucet drips, operate handle several times from "off" to "on". Do  
not apply excessive force.  
Clogged CARTRIDGE (4) inlets may cause reduced flow in "full on"  
hot or cold. To clean inlets, first turn off water supply, then:  
Remove HANDLE (1), CAP (2) and CARTRIDGE (4).  
Clean inlets and MANIFOLD (5).  
Reassemble CARTRIDGE (4), alternately tightening  
SCREWS (3). Replace CAP (2) and HANDLE (1).  
Check flow.  
5
4
1
CARTRIDGE  
INLETS  
3
2
CARE INSTRUCTIONS:  
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.  
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A  
CLOTH WITH A COARSE SURFACE.  
M968628 REV.1.3  
 

Actron Automobile KAL 3840 User Manual
Adcom Stereo Amplifier GTP 602 User Manual
Aiphone Intercom System IE DL1 User Manual
Alpine Car Stereo System IVA C800E User Manual
Altinex Network Card DA2000TM User Manual
Altinex Stereo Amplifier DA1226AT User Manual
Atlantic Indoor Furnishings 050202 User Manual
Atlona TV Cables ATP 14029 User Manual
Axor Plumbing Product 04170XX0 User Manual
Bakers Pride Oven Food Warmer MODEL MHC4 8 User Manual