Avital Remote Starter 3001 User Manual

FRONT COVER  
 
Table of Contents  
AviStart 3001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Remote Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Stealth Coding Technology. . . . . . . . . . . . . . . . . . . . . . . 2  
Electronic Scan Prevention (ESP). . . . . . . . . . . . . . . . . . . . . 3  
Instant Remote Control Code Deletion. . . . . . . . . . . . . . . . . . 3  
One-Step Remote Control Code Learning . . . . . . . . . . . . . . . . 3  
Valet Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Operating Your AviStart . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Remote Engine Start - Safety and Counter-Theft . . . . . . . . . . . . . 4  
Visual Fault Indication . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Remote-Controlled Door Lock/Unlock* . . . . . . . . . . . . . . . . . 4  
Remote Engine Start - Operation . . . . . . . . . . . . . . . . . . . . . 5  
User-Programmable Temperature-Controlled Starting . . . . . . . . . . 6  
Pit Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Protected Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
User-Programmable Features . . . . . . . . . . . . . . . . . . . . . . . 8  
Programming Table for System Features . . . . . . . . . . . . . . . . . 9  
Programming Table for Remote Controls . . . . . . . . . . . . . . . . . 9  
1
AviStart 3001 Owner's Manual  
 
AviStart 3001  
Congratulations! You have just purchased the AviStart 3001, a remote engine  
starter system manufactured by Avital Technologies, Inc. You are about to  
experience the convenience and luxury of being able to start your vehicle  
engine from the comfort of your home, office, department store or other  
remote location.  
To fully benefit from the capabilities of your AviStart system, we encourage  
you to read the Owner"s Manual thoroughly before using the system. If you  
have any problems or questions regarding your AviStart system, consult the  
dealer from whom you purchased this product.  
Lifetime Warranty  
Avital guarantees the operation of your AviStart control unit and remote  
control for as long as you own your car. (Please refer to the back of this  
manual for complete terms and conditions.)  
Remote Controls  
Included with your AviStart system is one 4-button/9-channel remote control.  
The remote control (remote) is a miniature transmitter powered by a small  
+12 volt battery. The RangeMaster™ super-heterodyne receiver (installed in  
your vehicle) allows your remote to command your system from up to ¼ mile  
away. Obstructions, electrical or radio interference, weather conditions,  
window tint or a weak battery can reduce this range. Your remote is the  
key to your AviStart system and can be used to lock and unlock your doors  
and start and stop your engine.  
The AviStart system can accept up to four Avital remote controls. Additional  
remote controls and remote control batteries can be purchased from any  
authorized Avital dealer. To locate an authorized dealer, or for other product  
information, visit Avital's web site atwww.avital.com .  
Stealth Coding Technology  
Stealth Coding technology offers the most advanced protection available  
against "code-grabbing" devices which thieves may use to record the digital  
code transmitted by your remote control. When you leave the area, thieves  
can then play back the code to start or stop your system. Avital"s remote  
controls with Stealth Coding randomly change the code every time you use  
them, and your system will not respond if any code is retransmitted. This  
technology makes code-grabbing devices useless.  
2
AviStart 3001 Owner's Manual  
 
Electronic Scan Prevention (ESP)  
Your AviStart system also includes ESP, which blocks electronic scanner codes  
preventing unauthorized operation of your system.  
Instant Remote Control Code Deletion  
In the event of a lost or stolen remote control, all remote controls can be  
erased from the system memory preventing unauthorized system operation.  
(See the "Programming Table for Remote Controls" on page 9).  
One-Step Remote Control Code Learning  
The AviStart system allows you to add new remote controls in one step. (See  
the "Programming Table for Remote Controls" on page 9).  
Valet Switch  
The valet switch is a small hidden toggle switch which allows you to control all  
of the system programmable features. (See "User-Programmable Features" on  
page 9). This switch can only be controlled with the use of your ignition key.  
NOTE: Be sure to have your dealer show you where the valet switch is located.  
3
AviStart 3001 Owner's Manual  
 
Operating Your AviStart  
Remote Engine Start - Safety and Counter-Theft  
I CAUTION : Be sure to read the "WARNING" bulletin on the inside  
cover of this manual before attempting to operate remote start.  
Automatic Safety and Counter-Theft Features  
Before remote starting your engine, the AviStart system will automatically  
perform a safety check to ensure the following conditions have been met:  
• Brake pedal is not depressed.  
• Engine and ignition are turned "OFF."  
• Hood is closed.  
After remote starting your engine, the AviStart system will shut off the engine  
immediately if the ignition is "OFF" and any of the following occurs:  
• The hood is opened.  
• The brake pedal is pressed.  
• The remote control START button is pressed.  
• The 20 minute run time expired.  
Visual Fault Indication  
When you press the remote control button to start your engine, AviStart's  
built-in fault detection system will automatically scan all of the safety zones. If  
a fault is detected, the system will prevent your engine from remote starting  
and provides a visual indication to show where the fault has occurred. The  
parking lights will flash 1 time if a hood switch fault is detected, 3 times if a  
brake switch fault is detected and 4 times if the system is in "Protected Valet  
Mode" (see page 7 for a description of this feature). If this occurs, you may  
need to bring your vehicle to your authorized Avital dealer for service.  
Remote-Controlled Door Lock/Unlock*  
To Lock the Doors  
C button for 1-2 seconds. The doors will lock and the  
Press the remote control  
parking lights will flash twice.  
* If your system was installed with this door lock/unlock feature,  
all other door lock/unlock related features will apply.  
4
AviStart 3001 Owner's Manual  
 
To Unlock the Doors  
Press the remote control  
and the parking lights will flash once.  
button for 1-2 seconds. The doors will unlock  
D
Remote Engine Start - Operation  
Your AviStart system will start your vehicle engine with a touch of a button on  
your remote control. Before remote starting, ensure the vehicle is in "Park" and  
the key is notin the ignition. To cool or warm the interior of your vehicle,  
preset the climate control to your preference (heater, defrost or air  
conditioning). Set the fan to a medium speed(not maximum).  
To Remote Start the Engine  
1.  
Press the remote control  
button for 1-2 seconds, 10-15 minutes before  
s
you enter your vehicle (this will allow the climate control time to heat or  
cool the interior.) The parking lights will flash 2 times, the engine will start  
and the parking lights will remain on as a visual indication that the engine  
is running.  
If you have a diesel engine, the AviStart will be programmed to start 15  
seconds after the parking lights flash 2 times or the vehicle glow plug light  
turns off. This will allow time for the glow plugs to heat up.  
2 . If the engine does not remote start, the AviStart system will attempt to start  
the engine two additional times.  
3 . If the vehicle is left unattended, the engine will run for 20 minutes and  
then shut off automatically.  
To Operate the Vehicle While Remote Started  
1.  
Press the remote controlD button for 1-2 seconds. The doors will unlock  
and the parking lights will flash once.  
2 . Enter the vehicle (do not touch the brake pedal), turn the ignition key to  
the "ON" position and then press the brake pedal. Pressing the brake pedal  
will shut off the remote start and parking lights but the engine will remain  
running.  
3. You can now drive the vehicle.  
To Shut Off Remote Start  
At any time after the engine has been remote started, you can shut off the  
engine with the remote control by pressing the remote control  
1-2 seconds. The engine and parking lights will shut off.  
button for  
L
5
AviStart 3001 Owner's Manual  
 
User-Programmable Temperature-Controlled Starting  
CAUTION : Do not activate Temperature-Controlled Starting while  
the vehicle is in an enclosed area.  
I
The AviStart system can be programmed to monitor the air temperature inside  
your vehicle and automatically start the vehicle engine whenever the  
temperature inside reaches or drops below a preprogrammed temperature  
level. There are three temperature levels to choose from. (This feature is  
programmed OFF from the factory and must be programmed ON to operate.  
See the "Programming Table for System Features"on page 9.)  
To Activate  
and C buttons at the same time for 1-2 seconds.  
Press the remote control  
The parking lights will turn on for 3 seconds, turn off for 1 second, turn on for  
s
3 seconds and then shut off. This will be your visual indication that you have  
activated the Temperature-Controlled Starting feature.  
The AviStart will monitor the air temperature every 2.5 hours and will only  
start the engine if the temperature inside the vehicle has reached or dropped  
below the preprogrammed temperature level. The parking lights will flash 2  
times, the vehicle will start and the parking lights will turn on. The vehicle will  
run for 10 minutes and then shut off. This will allow the engine to warm up  
and charge the battery.  
To Deactivate  
Press the remote control and  
buttons at the same time for 1-2 seconds.  
C
s
The parking lights will turn on for 3 seconds and then shut off. This will be  
your visual indication that you have deactivated the Temperature- Controlled  
Starting feature.  
NOTE: At any time, if the ignition key is turned "ON" or the vehicle is remote  
started, the Temperature-Controlled Starting feature will deactivate.  
Pit Stop Mode  
CAUTION: Do not leave passengers or pets in the vehicle while the  
system is in Pit Stop Mode.  
I
The Pit Stop Mode allows you to park the vehicle for short-term stops, remove  
the ignition key and leave the engine running.  
6
AviStart 3001 Owner's Manual  
 
To Activate  
1. While the vehicle engine is running with the ignition key turned "ON,"  
press the remote control button for 1-2 seconds. The parking lights will  
s
flash 2 times and stay on. (Make sure the vehicle is in "Park" and the  
parking brake is set.)  
2. Turn the ignition key "OFF" and the engine will stay running.  
3. Remove the ignition key and remote control and exit the vehicle.  
Remember to keep the ignition key and remote control in your  
possession.  
4.  
Press the remote control  
secure the vehicle.  
button for 1-2 seconds to lock the doors and  
C
To Deactivate  
1.  
Press the remote controlD button for 1-2 seconds to unlock the doors.  
2. Enter the vehicle (do not touch the brake pedal), turn the ignition key to  
the "ON" position and then press the brake pedal. The parking lights will  
shut off and you will now be able to drive the vehicle.  
Protected Valet Mode  
You should place your system in Protected Valet Mode whenever your vehicle  
is being serviced by mechanics, car wash personnel or driven by valet parking  
attendants. While in the Protected Valet Mode, all remote start functions are  
bypassed to prevent unauthorized or accidental operation. If a remote start is  
attempted, the parking lights will flash 4 times and the vehicle will not start.  
To Turn on Protected Valet Mode  
1. Turn the ignition key to the "ON" position or start the engine.  
2. Flick the valet switch to the "ON" position.  
3. Turn the ignition key to the "OFF" position.  
To Turn off Protected Valet Mode  
1. Turn the ignition key to the "ON" position or start the engine.  
2. Flick the valet switch to the "OFF" position.  
3. Turn the ignition key to the "OFF" position.  
7
AviStart 3001 Owner's Manual  
 
User-Programmable Features  
All AviStart system and remote control programmable features are  
accomplished by turning the ignition key "ON" (or starting the engine) and  
flicking the valet switch on and off a preset number of times.  
The AviStart also allows you to add new remote controls in one step, delete  
lost or stolen remote controls or rearrange the factory preset remote control  
functions.  
1 . Remove the system from Protected Valet Mode. Programming cannot be  
accessed while the system is in Protected Valet Mode.  
2. Select the feature you wish to program from the "Programming Table for  
System Features" or the "Programming Table for Remote Controls" on  
page 9. Note the number of beeps associated with that feature.  
3. Turn the ignition key to the "ON" position.  
4. Within 10 seconds, begin flicking the valet switch on and off. The piezo  
beeper will beep once each time you flick the switch on then off.  
5. Continue flicking the switch on and off, counting the number of beeps.  
NOTE: Stop when you reach the number of beeps associated with your  
chosen feature.  
6 . Follow the "Secondary Action." You will hear a number of beeps to  
confirm that you have changed the setting of that feature.  
7 . Turn the ignition key to the "OFF" position.  
8. Repeat steps 1-7 for any other feature you wish to program.  
8
AviStart 3001 Owner's Manual  
 
Programming Table for System Features  
Factory No. of  
Feature  
Secondary Action  
Setting  
beeps  
Wait 3 seconds. The piezo beeper  
will beep once for OFF, twice for  
5°F (-15°C).  
Temperature-Controlled Starting  
OFF  
5
OFF or 5 °F (-15 °C)  
Wait 3 seconds. The piezo beeper  
will beep once for -7°F (-20°C),  
twice for -22° F (-30 °C).  
Temperature-Controlled Starting  
8
-7°F (-20 °C) or -22°F (-30 °C)  
Programming Table for Remote Controls  
Factory  
Setting  
No. of  
beeps  
Feature  
Secondary Action  
Press the  
Button, the piezo  
C
Door Lock  
10  
C Button  
beeper will beep 1 time.  
Press the Button, the piezo  
D
Door Unlock  
11  
12  
13  
14  
15  
D Button  
beeper will beep 1 time.  
Press the  
Button, the piezo  
s Button  
Remote Engine Start  
Remote Engine Stop  
s
beeper will beep 2 times.  
Press theL Button, the piezo  
beeper will beep 3 times.  
L Button  
Temperature-Controlled  
Remote Engine Start  
Press the  
+
Buttons, the piezo  
C
C +  
s Buttons  
s
beeper will beep 4 times.  
One Step Remote Control  
Code Learning  
Press the Button, the piezo  
C
Button  
C
beeper will beep 1 time.  
Wait 3 seconds, the piezo beeper  
will beep twice. All codes are  
erased out of memory.  
Instant Remote Control  
Code Deletion  
16  
9
AviStart 3001 Owner's Manual  
 
LifetimeLimitedFactoryWarranty-TermsandConditions  
Avitalvehiclesecuritysystemsandaccessoriesrequireprofessionalinstallationby an Authorized  
Avital Dealer. Un less the sys tem is sold and in stalled by an Authorized Avital Dealer, all prod uct  
war ran ties are void. As the manu fac turer, Avital Technologies war rants to the origi nal con su mer  
pur chaser, the sys tem con trol unit and re mote con trols to be free from de fects in ma te rial and  
work man ship for as long as you own the ve hi cle in which the sys tem was origi nally in stalled. All  
other parts of the sys tem and ac ces so ries to the sys tem are war ranted to be free from de fect s in  
ma te rial and work man ship for one (1) year from the date of pur chase. Avital Technologies will  
repair or replace, at its option and free of charge during the warranty period, any system  
componentthatprovesdefectiveinmaterialorworkmanshipundernormalinstallation,use,and  
service, provided the product is returned to our factory by an Authorized Avital Dealer,  
transportation charges prepaid. Products returned to our factory must be accompaniedbya  
pho to copy of the pur chase re ceipt. In the ab sence of such pur chase re ceipt, the war ranty pe riod  
shall be one (1) year from the date of manu fac ture. Any dam age to the prod uct(s) as a re sult o f  
misuse,abuse,neglect,accident,incorrectwiring,improperinstallation,destruction oralteration  
of the se rial number, re pair or al tera tion out side our fac tory, or any use vio la tive of in structions  
fur nished by us will void the war ranty. This war ranty is lim ited to de fec tive parts and spe c ifically  
excludes any in ci den tal or con se quen tial dam ages con nected there with. This warranty is no t  
transferable. Avital Technologies makes no war ranty against theft. This war ranty is not to be  
construed as an insurance policy against loss. Warranty on installation labor, removal an d  
reinstallationchargesarenottheresponsibilityofAvitalTechnologies,Inc.  
ONLINE REGISTRATION: For your convenience, we now provide online  
registration for your Avital purchase. Within 10 days of purchase, register at  
your Owner's Manual, as well as information on product updates or special  
promotions.  
Your system serial number is:  
Place se rial number sticker here  
© 1999 Avital Technologies, Inc., A Division of Clifford Electronics  
Part Number: 31-3001/AviStart3001OM/0999  
 

3Com Gas Grill GNS 430 430A User Manual
Acer Personal Computer 2430 User Manual
Adaptec Network Card AUA 3121 User Manual
AEG Cooktop FM600KM B User Manual
AEG Power Supply 3M 2 User Manual
Apple Network Card PCI E x8 User Manual
Bakers Pride Oven Oven CBBQ 30S BI User Manual
Baldor Portable Generator MN2410 User Manual
Banner American Products Network Card Wireless Network User Manual
Beko Ice Maker GNE V322 X User Manual