Eureka Tents Tent Condo User Manual

5. Attach the top two clips from the tent’s roof to  
this pole. See fig.4.  
11. Attach the fly. With top side up, on  
ground at the front of the tent, arrange the fly into the same  
rectangle as the tent.  
ASSEMBLY INSTRUCTIONS  
FOR THE CONDO TENT:  
6. Slide a second long pole onto the hub arm that  
points to B. Disconnect the last section of this pole  
and insert the pin into the bottom of the remaining  
section. Attach two top clips, from the roof, to this  
pole. Repeat at C and D, partially raising the tent  
as you work. See fig. 5.  
NOTE: The fly is not symmetrical; it only fits one way.  
Make sure the green web buckle on the fly matches up  
with the green web buckle on the tent and that the tan web  
buckle matches with the tan on the tent.  
Component List:  
1 Tent Body,  
1 Carry Bag,  
4 Long Poles  
2 Side Poles,  
1 Tent Fly,  
1 Stake Bag and Stakes, 1 Pole Bag  
fig. 4  
Grasp the corners of the narrow end of the fly and drag them  
up and over the poles to completely cover the roof. ( This is  
much easier with two people. ) The skylight window in the fly  
should align with the zippered vent in the sleeping section of  
the tent.  
F
ASSEMBLY: It is difficult to assemble this tent alone. It is a large  
tent and we recommend that you have help.  
fig. 5  
1. Remove from the carry bag and separate all the components.  
Unroll and unfold the fabric, top side up, on a clean, dry space  
and open the doors. If windy, stake down the windward corner.  
Remove the protective cover from the center hub.  
B
C
At the corners, reach under the fly and attach the hook & loop  
straps to the tent poles securing the fly in place.  
2. Assemble the shockcorded poles and divide according to size  
and shape. Take care; make sure that each pole section is fully  
seated into the next. Do not allow the sections to snap together  
as this can damage the ends.  
Fasten the side release buckles and adjust tension until the  
wrinkles are gone. See fig. 8.  
D
E
3. Orient the hub so that the two arms, with the most downward  
taper, point to the sides of the tent. Take care; make sure that the  
fabric is not twisted.  
Important: If the hub arms point in the wrong direction, the hub  
could break under the stress of assembly.  
A
7. Slide a side pole onto the hub arm from the side of the tent at E.  
Clip the top two tent clips onto the frame. Disconnect the bottom  
section and insert the pin into the end of the second section.  
Repeat with the last pole on the opposite side at F.  
4. Slide the hub arm, facing A, into the reinforced end of a long  
pole. See fig.1. Disconnect the last section at the bottom end of  
this pole. Insert a pin from the tent’s floor, into the end of the  
second section. See fig. 2. & fig. 3.  
8. Raise the tent. Grasp the pole where it’s connected to the ring  
and pin, lift the corner off the ground and remove the pin.  
Reconnect the last section and reinsert the pin. Repeat with  
remaining poles until the tent is at full height and freestanding.  
fig. 8  
9. Attach all clips to the poles and attach the corner shockcords to  
fig 1  
fig 2  
the J-hooks at the elbow of each corner pole. See fig. 6.  
YOUR TENT IS READY !  
STORM CURTAINS: Storm Curtains zip into the fly to offer full weather  
protection. Detach the buckles at the corners of the tent. Take the curtain  
that corresponds with the opening to be covered. The curtains are made  
in pairs: Front side right, front side left. Rear side right, rear side left. The  
front and back curtains are identical and can be used in either location.  
Zip the curtain into place and reconnect the buckles.  
fig. 6  
F
C
B
STORM RINGS: The tent is equipped with storm rings on the fly. In windy  
conditions, use 1/8” to 1/4 x 12’ guylines and these rings to anchor the  
tent down.  
TAKE DOWN: Pull up stakes. Release the fly's hook & loop straps and  
buckles. Remove fly. Remove clips from poles and pull poles off of the  
pins. Collapse the tent poles and stow. Fold the tent onto itself then fold  
the fly and lay it on tent. Roll up both towards the door and stow.  
10. Stake the tent down. Drive stakes to capture  
the rings at the base of each pole. See fig. 7. Stake  
one corner, pull the fabric taut, dressing out the  
D
A
floor as you work your way around the tent.  
E
fig. 7  
fig 3  
AVAILABLE OPTIONS: Floor Saver, Gear Loft  
REV E 4.09  
 

3Com Planer 3CRWE73796B User Manual
Actiontec electronic Network Card HPE200AV User Manual
Acumen Heart Rate Monitor HR427 User Manual
Agri Fab Lawn Sweeper 45 0352 User Manual
Airlink Switch UG AGIGA5SW 1105 User Manual
Alesis CD Player CD Twin Portable CD Backup and Copy System User Manual
Alliance Laundry Systems Washer Dryer CPD6C User Manual
Altec Lansing Portable Speaker iMT702 User Manual
American Standard Plumbing Product 705205 User Manual
Barco Camera Accessories R5976663 01 User Manual